IBM 4800-741 Operation Guide - Page 97

Installing, mount

Get IBM 4800-741 PDF manuals and user guides View all IBM 4800-741 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Updated October 31, 2007 Installing a CRT on a post mount 1. Switch the power OFF. 2. Place the CRT upside down on a table or counter. 3. Thread the power cord and video cable of the CRT through the tilt/swivel. 4. Place the hooks of the mount into the base of the CRT and slide the mount forward. Note: Route the cables through the cutout in the tilt/swivel assembly. 5. Thread the power cables and the video cables down through the post. 6. If you are installing on a base, open the cable cover and pull the cables out through the opening. If you are bolting the post to a counter top, pull the cables straight through the bottom opening. Figure 75. Attaching the CRT to a post mount 7. Attach the tilt/swivel to the post with one screw. 8. If you are using a base, attach the post to the base with four screws. 9. Turn the CRT right side up and place it on the counter. 10. If you are not using a base, bolt the post to the counter. 11. Attach the CRT's signal cable to the video port on the system unit. 12. Plug the display power cord into a wall outlet using an adapter cable, or into the uninterruptible power supply (if installed). 13. Power ON the SurePOS 700. Chapter 4. Installing external options 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Installing
a
CRT
on
a
post
mount
1.
Switch
the
power
OFF.
2.
Place
the
CRT
upside
down
on
a
table
or
counter.
3.
Thread
the
power
cord
and
video
cable
of
the
CRT
through
the
tilt/swivel.
4.
Place
the
hooks
of
the
mount
into
the
base
of
the
CRT
and
slide
the
mount
forward.
Note:
Route
the
cables
through
the
cutout
in
the
tilt/swivel
assembly.
5.
Thread
the
power
cables
and
the
video
cables
down
through
the
post.
6.
If
you
are
installing
on
a
base,
open
the
cable
cover
and
pull
the
cables
out
through
the
opening.
If
you
are
bolting
the
post
to
a
counter
top,
pull
the
cables
straight
through
the
bottom
opening.
7.
Attach
the
tilt/swivel
to
the
post
with
one
screw.
8.
If
you
are
using
a
base,
attach
the
post
to
the
base
with
four
screws.
9.
Turn
the
CRT
right
side
up
and
place
it
on
the
counter.
10.
If
you
are
not
using
a
base,
bolt
the
post
to
the
counter.
11.
Attach
the
CRT’s
signal
cable
to
the
video
port
on
the
system
unit.
12.
Plug
the
display
power
cord
into
a
wall
outlet
using
an
adapter
cable,
or
into
the
uninterruptible
power
supply
(if
installed).
13.
Power
ON
the
SurePOS
700.
Figure
75.
Attaching
the
CRT
to
a
post
mount
Updated
October
31,
2007
Chapter
4.
Installing
external
options
77