IBM HS12 User Guide - Page 27

Opening the blade server cover, Attention

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Release handles (open) Attention: v To maintain proper system cooling, do not operate the BladeCenter unit without a blade server, expansion unit, or filler module installed in each blade server bay. v When you remove the blade server, note the blade-server bay number. Reinstalling a blade server into a different blade server bay from the one it was removed from can have unintended consequences. Some configuration information and update options are established according to blade-server bay number; if you reinstall the blade server into a different bay, you might have to reconfigure the blade server. To remove the blade server, complete the following steps: 1. If the blade server is operating, shut down the operating system; then, press the power-control button (behind the blade server control panel door) to turn off the blade server (see "Turning off the blade server" on page 13 for more information). Attention: Wait at least 30 seconds, until the storage devices stop spinning, before you proceed to the next step. 2. Open the two release handles as shown in the illustration. The blade server moves out of the blade server bay approximately 0.6 cm (0.25 inch). 3. Pull the blade server out of the bay. 4. Place either a blade filler or another blade server in the blade server bay within 1 minute. Opening the blade server cover Use these instructions to open the blade server cover. To open the blade server cover, complete the following steps. Note: 1. The following illustration shows how to open the cover on the blade server. 2. The illustrations in this document might differ slightly from your hardware. Chapter 3. Installing options 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Release handles
(open)
Attention:
v
To maintain proper system cooling, do not operate the BladeCenter unit without
a blade server, expansion unit, or filler module installed in each blade server
bay.
v
When you remove the blade server, note the blade-server bay number.
Reinstalling a blade server into a different blade server bay from the one it was
removed from can have unintended consequences. Some configuration
information and update options are established according to blade-server bay
number; if you reinstall the blade server into a different bay, you might have to
reconfigure the blade server.
To remove the blade server, complete the following steps:
1.
If the blade server is operating, shut down the operating system; then, press the
power-control button (behind the blade server control panel door) to turn off
the blade server (see “Turning off the blade server” on page 13 for more
information).
Attention:
Wait at least 30 seconds, until the storage devices stop spinning,
before you proceed to the next step.
2.
Open the two release handles as shown in the illustration. The blade server
moves out of the blade server bay approximately 0.6 cm (0.25 inch).
3.
Pull the blade server out of the bay.
4.
Place either a blade filler or another blade server in the blade server bay within
1 minute.
Opening the blade server cover
Use these instructions to open the blade server cover.
To open the blade server cover, complete the following steps.
Note:
1.
The following illustration shows how to open the cover on the blade server.
2.
The illustrations in this document might differ slightly from your hardware.
Chapter 3. Installing options
17