IBM HS12 User Guide - Page 34

Installing a concurrent KVM card, Important, Notes

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

tabs are fully seated. When the DIMM is correctly installed, the retaining clips are parallel to the sides of the DIMM. Important: If there is a gap between the DIMM and the retaining clips, the DIMM has not been correctly installed. In this case, open the retaining clips and remove the DIMM; then, reinsert the DIMM. If you have other devices to install or remove, do so now; otherwise, go to "Completing the installation" on page 30. Installing a concurrent KVM card Use these instructions to install a concurrent KVM (CKVM) card in the blade server. To install a cKVM card, complete the following steps. Notes: 1. The following illustration shows the location and how to install a cKVM card in the system board. 2. The illustrations in this document might differ slightly from your hardware. cKVM card 1. Before you begin, read "Safety" on page v and "Installation guidelines" on page 15. 2. If the blade server is installed in a BladeCenter unit, remove it (see "Removing the blade server from the BladeCenter unit" on page 16 for instructions). 3. Carefully lay the blade server on a flat, static-protective surface. 4. Open the blade server cover (see "Opening the blade server cover" on page 17 for instructions). 24 BladeCenter HS12 Type 8014 or 8028: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
tabs are fully seated. When the DIMM is correctly installed, the retaining
clips are parallel to the sides of the DIMM.
Important:
If there is a gap between the DIMM and the retaining clips, the
DIMM has not been correctly installed. In this case, open the retaining clips
and remove the DIMM; then, reinsert the DIMM.
If you have other devices to install or remove, do so now; otherwise, go to
“Completing the installation” on page 30.
Installing a concurrent KVM card
Use these instructions to install a concurrent KVM (CKVM) card in the blade
server.
To install a cKVM card, complete the following steps.
Notes:
1.
The following illustration shows the location and how to install a cKVM card
in the system board.
2.
The illustrations in this document might differ slightly from your hardware.
cKVM card
1.
Before you begin, read “Safety” on page v and “Installation guidelines” on
page 15.
2.
If the blade server is installed in a BladeCenter unit, remove it (see
“Removing the blade server from the BladeCenter unit” on page 16 for
instructions).
3.
Carefully lay the blade server on a flat, static-protective surface.
4.
Open the blade server cover (see “Opening the blade server cover” on page 17
for instructions).
24
BladeCenter HS12 Type 8014 or 8028: Installation and User's Guide