IBM HS12 User Guide - Page 59

ServerGuide problems, Symptom, Suggested action

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

ServerGuide problems Use this information to locate ServerGuide problems and suggested actions. The following table lists problem symptoms and suggested solutions. Symptom Suggested action The ServerGuide Setup and Installation CD will not start. v Make sure that the CD drive is associated with the blade server that you are configuring. v Make sure that the blade server supports the ServerGuide program and has a bootable CD (or DVD) drive. v If the startup (boot) sequence settings have been changed, make sure that the CD drive is first in the startup sequence. The RAID configuration program cannot view all installed drives, or the operating system cannot be installed. v Make sure that there are no duplicate SCSI/SAS IDs or interrupt request (IRQ) assignments. See "Configuring a SAS RAID array" on page 42. v Make sure that the storage drive is connected correctly. See "Blade server connectors" on page 14 to locate the storage drive connector. The operating-system installation program continuously loops. Make more space available on the hard disk. The ServerGuide program will not start the operating-system CD. Make sure that the operating-system CD is supported by the ServerGuide program. See the ServerGuide Setup and Installation CD label for a list of supported operating-system versions. The operating system cannot be installed; the option is not available. Make sure that the operating system is supported on the blade server. If the operating system is supported, either no logical drive is defined (SCSI/SAS RAID systems) or the ServerGuide System Partition is not present. Run the ServerGuide program and make sure that setup is complete. Chapter 6. Solving problems 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
ServerGuide problems
Use this information to locate ServerGuide problems and suggested actions.
The following table lists problem symptoms and suggested solutions.
Symptom
Suggested action
The
ServerGuide Setup and
Installation
CD will not start.
v
Make sure that the CD drive is associated with the blade server that you are
configuring.
v
Make sure that the blade server supports the ServerGuide program and has a
bootable CD (or DVD) drive.
v
If the startup (boot) sequence settings have been changed, make sure that the
CD drive is first in the startup sequence.
The RAID configuration
program cannot view all
installed drives, or the
operating system cannot be
installed.
v
Make sure that there are no duplicate SCSI/SAS IDs or interrupt request (IRQ)
assignments. See “Configuring a SAS RAID array” on page 42.
v
Make sure that the storage drive is connected correctly. See “Blade server
connectors” on page 14 to locate the storage drive connector.
The operating-system
installation program
continuously loops.
Make more space available on the hard disk.
The ServerGuide program will
not start the operating-system
CD.
Make sure that the operating-system CD is supported by the ServerGuide
program. See the
ServerGuide Setup and Installation
CD label for a list of supported
operating-system versions.
The operating system cannot be
installed; the option is not
available.
Make sure that the operating system is supported on the blade server. If the
operating system is supported, either no logical drive is defined (SCSI/SAS RAID
systems) or the ServerGuide System Partition is not present. Run the ServerGuide
program and make sure that setup is complete.
Chapter 6. Solving problems
49