IBM HS12 User Guide - Page 40

Completing the installation, source. Always replace the blade server cover before installing the blade

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

3. Remove the protective covers from the blade server expansion connectors, if any are present. 4. Touch the static-protective package that contains the optional expansion unit to any unpainted metal surface on the BladeCenter unit or any unpainted metal surface on any other grounded rack component; then, remove the optional expansion unit from the package. 5. Orient the optional expansion unit as shown in the illustration. 6. Lower the optional expansion unit so that the slots at the rear slide down onto the cover pins at the rear of the blade server. 7. Close the optional expansion unit (see the expansion unit documentation for information and instructions): v If the optional expansion unit has an extraction device, pivot the expansion unit closed; then, use the extraction device to fully seat the expansion unit on the system board. These extraction devices can be of several types, including thumbscrews or levers. v If the optional expansion unit has no extraction device, pivot the expansion unit closed; then, press the expansion unit firmly into place until the blade server cover releases click. The connectors on the expansion unit automatically align with and connect to the connectors in the system board. If you have other expansion units to install, do so now; otherwise, go to "Completing the installation." Completing the installation To complete the installation, complete the following tasks. 1. Reinstall the optional expansion unit, if you removed one to install other devices (see "Installing an optional expansion unit" on page 29 for information on installing the expansion unit). 2. Close the blade server cover, unless you installed an optional expansion unit that has its own cover (see "Closing the blade server cover" on page 31). Statement 21 CAUTION: Hazardous energy is present when the blade server is connected to the power source. Always replace the blade server cover before installing the blade server. 3. Reinstall the blade server into the BladeCenter unit (see "Installing the blade server in a BladeCenter unit" on page 31). 4. Turn on the blade server (see "Turning on the blade server" on page 13). 5. For certain devices, run the blade server Configuration/Setup Utility program (see Chapter 4, "Configuring the blade server," on page 35). Note: If you have just connected the power cords of the BladeCenter unit to electrical outlets, you must wait until the power-on LED on the blade server flashes slowly before you press the power-control button. 30 BladeCenter HS12 Type 8014 or 8028: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
3.
Remove the protective covers from the blade server expansion connectors, if
any are present.
4.
Touch the static-protective package that contains the optional expansion unit to
any
unpainted
metal surface on the BladeCenter unit or any
unpainted
metal
surface on any other grounded rack component; then, remove the optional
expansion unit from the package.
5.
Orient the optional expansion unit as shown in the illustration.
6.
Lower the optional expansion unit so that the slots at the rear slide down onto
the cover pins at the rear of the blade server.
7.
Close the optional expansion unit (see the expansion unit documentation for
information and instructions):
v
If the optional expansion unit has an extraction device, pivot the expansion
unit closed; then, use the extraction device to fully seat the expansion unit on
the system board. These extraction devices can be of several types, including
thumbscrews or levers.
v
If the optional expansion unit has no extraction device, pivot the expansion
unit closed; then, press the expansion unit firmly into place until the blade
server cover releases click.
The connectors on the expansion unit automatically align with and connect to the
connectors in the system board.
If you have other expansion units to install, do so now; otherwise, go to
“Completing the installation.”
Completing the installation
To complete the installation, complete the following tasks.
1.
Reinstall the optional expansion unit, if you removed one to install other
devices (see “Installing an optional expansion unit” on page 29 for information
on installing the expansion unit).
2.
Close the blade server cover, unless you installed an optional expansion unit
that has its own cover (see “Closing the blade server cover” on page 31).
Statement 21
CAUTION:
Hazardous energy is present when the blade server is connected to the power
source. Always replace the blade server cover before installing the blade
server.
3.
Reinstall the blade server into the BladeCenter unit (see “Installing the blade
server in a BladeCenter unit” on page 31).
4.
Turn on the blade server (see “Turning on the blade server” on page 13).
5.
For certain devices, run the blade server Configuration/Setup Utility program
(see Chapter 4, “Configuring the blade server,” on page 35).
Note:
If you have just connected the power cords of the BladeCenter unit to
electrical outlets, you must wait until the power-on LED on the blade server
flashes slowly before you press the power-control button.
30
BladeCenter HS12 Type 8014 or 8028: Installation and User's Guide