IC Realtime ICIP-B3732Z Product Manual - Page 48

Connection, 2.2.1 Connection

Get IC Realtime ICIP-B3732Z PDF manuals and user guides View all IC Realtime ICIP-B3732Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Preferred DNS DNS IP address. Alternate DNS Alternate DNS IP address. Enable ARP/Ping set device IP address service. You can use ARP/Ping command to modify or set the device IP address if you know the device MAC address. Before the operation, please make sure the network camera and the PC in the same LAN. This function is on by default. You can refer to the steps listed below. Step 1: Get an IP address. Set the network camera and the PC in the same LAN. Step 2: Get the physical address from the label of the network camera. Step 3: Go to the Run interface and then input the following commands. arp -s ping -l 480 -t Such as：arp -s 192.168.0.125 11-40-8c-18-10-11 ping -l 480 -t 192.168.0.125 Step 4: Reboot the device. Step 5: You can see the setup is OK if you can see there are output information such as "Reply from 192.168.0.125 ..." from the command output lines. Now you can close the command line. Step 6: Open the browse and then input http://. Click the Enter button, you can access now. 5.2.2 Connection 5.2.2.1 Connection The connection interface is shown as in Figure 5- 19. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
44
Preferred DNS
DNS IP address.
Alternate DNS
Alternate DNS IP address.
Enable
ARP/Ping set
device IP
address service.
You can use ARP/Ping command to modify or set the device IP
address if you know the device MAC address.
Before the operation, please make sure the network camera
and the PC in the same LAN. This function is on by default.
You can refer to the steps listed below.
Step 1
: Get an IP address. Set the network camera and the PC
in the same LAN.
Step 2
: Get the physical address from the label of the network
camera.
Step 3
: Go to the Run interface and then input the following
commands.
arp
–
s
<IP Address>
<MAC>
ping
–
l
480
–
t
<IP Address>
Such as
：
arp
-s
192.168.0.125
11-40-8c-18-10-11
ping
-l
480
-t
192.168.0.125
Step 4
: Reboot the device.
Step 5
: You can see the setup is OK if you can see there are
output information such as “Reply from 192.168.0.125 …” from
the command output lines.
Now you can close the command
line.
Step 6
: Open the browse and then input http://<IP
addres>.
Click the Enter button, you can access now.
5.2.2 Connection
5.2.2.1 Connection
The connection interface is shown as in
Figure 5-
19.