Icom IC-PW1 Instruction Manual - Page 15
Programming the CI-V address
View all Icom IC-PW1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
3 OPERATION s Programming the CI-V address The IC-PW1 uses CI-V frequency data for automatic selection of the operating band. Program the exciter's address to use this capability as follows: For non-Icom exciters, the IC-PW1 cannot be controlled using the CI-V function, so this setting is not necessary. For transceivers which have multiple antenna connectors for specified bands (e.g. IC-726, IC-729, etc.), set the same as for 2 Icom exciters. D Setting the Icom exciters When connecting 2 or more CI-V devices: DO NOT use the "AUTO" baud rate for CI-V devices. We recommend that all CI-V devices are set to 9600 bps. • When using the same baud rate, the exciters' frequencies are synchronized. • When using different baud rates (i.e. 4800 and 9600 bps, etc.), the exciters' frequencies are not synchronized. q Confirm that the exciter's CI-V transceive function is ON. - Refer to the instruction manual for details. w When connecting 2 exciters, connect the 1st and 2nd exciter to [INPUT1] and [INPUT2], respectively. e When connecting 2 Icom exciters, set [EXCITER] to the [1&2] position. r When connecting 2 or more CI-V devices, DO NOT set to "AUTO" baud rate. - Refer to the instruction manual for details. - When using the same baud rate, the exciters' frequencies are synchronized. - When using different baud rates (i.e. 4800 and 9600 bps, etc.), the exciters' frequencies are not synchronized. [INPUT z] and [INPUT x] selection is automatically selected using the exciter's baud rate. w Rotate the Icom exciter's tuning dial until the [INPUT z] light continuously lights. e Push [POWER] to turn the IC-PW1 power OFF and complete the setting. D When using 2 exciter's q When using 2 Icom exciters, be sure that [EXCITER] is set to the [1&2] position. w While pushing [INPUT], push [POWER] to enter the CI-V address programming mode. - [INPUT z] blinks. POWER TRANSMIT HF/50MHz ALL BAND 1kW LINEAR AMPLIFIER iPW1 Po ID TEMP VD SWR ALC TUNER METER-1 METER-2 AMP/ DOWN AUTO 1.8 3.5 7 10 14 18 21 24 28 50 UP PROTECT z x INPUT z x c v ANT e Push [DOWN]. - The band indicators, [1.8]-[50], light continuously. r Rotate the 1st Icom exciter's tuning dial until the [INPUT z] light continuously lights. t When 1 Icom exciter and 1 non-Icom exciter are connected, turn the power OFF to complete the setting. When 2 Icom exciters are connected, push [INPUT]. - [INPUT x] blinks when [INPUT] is pushed. y Rotate the 2nd Icom exciter's tuning dial until the [INPUT x] light continuously lights. u Push [POWER] to complete the setting. D Setting the IC-PW1's CI-V address It is not necessary to change the IC-PW1's default CI-V address of 54H. However, if desired, the address can be changed using the internal address switch illustrated below. D When using 1 Icom exciter q While pushing [INPUT], push [POWER] to enter the CI-V address programming mode. - [INPUT z] blinks. POWER TRANSMIT HF/50MHz ALL BAND 1kW LINEAR AMPLIFIER iPW1 Po ID TEMP VD SWR ALC TUNER METER-1 METER-2 AMP/ DOWN AUTO 1.8 3.5 7 10 14 18 21 24 28 50 UP PROTECT z x INPUT z x c v ANT 12