Icom IC-R8600 Ci-v Reference Guide

Icom IC-R8600 Manual

Get Icom IC-R8600 PDF manuals and user guides View all Icom IC-R8600 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-R8600 manual content summary:

  • Icom IC-R8600 | Ci-v Reference Guide - Page 1
    CI-V REFERENCE GUIDE COMMUNICATIONS RECEIVER iR8600
  • Icom IC-R8600 | Ci-v Reference Guide - Page 2
    Table of contents REMOTE CONTROL 2 ■■REMOTE CONTROL (CI-V) INFORMATION 2 DDCI-V connection 2 DDPreparation 2 DDData format 2 DDCommand table 3 DDCommand formats 9 1
  • Icom IC-R8600 | Ci-v Reference Guide - Page 3
    type, user supplied) to connect the IC-R8600 and the PC (controller). The required USB driver and driver installation guide can be downloaded from the Icom web site. Go to "http://www.icom.co.jp/world," and then click "Support," "Firmware Updates / Software downloads" in sequence. LThe download
  • Icom IC-R8600 | Ci-v Reference Guide - Page 4
    (30 dB) Select antenna (only 10 kHz - 29.999999 MHz) (00=ANT1, 01=ANT2, 02=ANT3) Speech all parameters (Signal level + Frequency + Receiving mode) Speech frequency (Signal level + Frequency) Speech receiving mode LThe mode is announced after the ongoing speech. Send/read the AF gain level (0000
  • Icom IC-R8600 | Ci-v Reference Guide - Page 5
    00 ~ 02 Send/read the Manual notch width (00=WIDE, 01=MID, 02=NAR) 00/02 Send/read the D-STAR digital squelch (D.SQL) setting (00=OFF, 02=CSQL) 00/ function status (00=OFF, 01=ON) Turn OFF the receiver Turn ON the receiver*1 Read the receiver ID See pp. 11 ~ 14 Send/read memory channel
  • Icom IC-R8600 | Ci-v Reference Guide - Page 6
    AM mode (00=Auto, 01=Manual, 02=Auto/Manual) Send/read the [NOTCH] key action in the SSB mode (00=Auto, 01=Manual, 02=Auto/Manual) Send/read SSB/CW synchronous ~ 0511=100%) Send/read the receive mode when [DIAL B] is pushed in the DIGITAL mode (00=Auto, 01=Digital, 02=Analog) Send/read the RX history
  • Icom IC-R8600 | Ci-v Reference Guide - Page 7
    02 Send/read the receiver's reference frequency signal source (00=IN Uses an external reference signal, 01=OFF, 02 0114 See p. 10 Send/read the nickname of the IC-R8600 (1 ~ 16 characters) 0115 0000 ~ 0255 Send/ width is displayed when you select the Manual Notch.) Send/read the digital TWIN
  • Icom IC-R8600 | Ci-v Reference Guide - Page 8
    Send/read the FSK FFT scope waveform averaging function setting (00=OFF, 01=2, 02=3, 03=4) Send/read the color of the FSK FFT scope waveform (000000000000 ~ (Frequency) (00=OFF, 01=ON) Send/read the text font color for received FSK signal See p. 10 Send/read the text font color for the time stamp
  • Icom IC-R8600 | Ci-v Reference Guide - Page 9
    the Scope Center mode or Fixed mode setting 02 See p. 19 Read the D-STAR message contained in the received signal 02 00* 00/01 Send/read the D- When using 4800 bps 02 20 07 00* See p. 22 Read the P25 ID 00/01 Send/read the P25 RX status output Preamble R8600's Controller's Command Sub
  • Icom IC-R8600 | Ci-v Reference Guide - Page 10
    that case, "FIL1" is selected with command 01 and the default filter setting of the receiving mode is automatically selected with command 06. Band edge frequency Command: 02, 1A 0F q w e r t y u i o !0 !1 !2 XX XXXXXXXXXX 2 DXXXXXXXXXX Edge number 01~XX* 10 Hz digit: 0 ~ 9 1 Hz digit: 0 ~ 9 1 kHz
  • Icom IC-R8600 | Ci-v Reference Guide - Page 11
    Remote control DDCommand formats (Continued) RX HPF/LPF setting for each operating mode Command: 1A 05 0 001, 0009, 0012, 0015, 0018, 0021, 0024, 0027, 0030, 0033 XXXX LPF (Band upper side) HPF (Band lower side) LPF 05 ~ 24=500 ~ 2400 Hz 25 =Through HPF 00 =Through 01 ~ 20=100 ~ 2000 Hz (The HPF
  • Icom IC-R8600 | Ci-v Reference Guide - Page 12
    SKIP 2 = PSKIP 0 =OFF 1 ~ 9=★1 ~ ★9 LSet "00" for the Programmable Scan Edge channel. y ~ !0 Receiving frequency Refer to "Receiving frequency" (p. 9) !1, !2 Receiving mode Refer to "Receiving mode" (p. 9) !3 Duplex setting !3 0X 0 (Fixed) 0 = OFF 1 = DUP- 2 = DUP+ !4 ~ !7 Offset frequency
  • Icom IC-R8600 | Ci-v Reference Guide - Page 13
    1 = TSQL 2 = DTCS $3 ~ $5 Tone squelch frequency Refer to "TSQL frequency" (p. 18) $6 ~ $8 DTCS code Refer to "DTCS code" (p. 18) For receiving a D-STAR signal $2 $3 XXXX $2 Digital squelch (D.SQL) type $2 0X 0 (Fixed) 0 = OFF 2 = CSQL $3 Digital code squelch (CSQL) code $3 XX Once position
  • Icom IC-R8600 | Ci-v Reference Guide - Page 14
    key $7 $8 $9 0XXXXX Once position: 0 ~ 9 10th position: 0 ~ 9 100th position: 0 ~ 9 1000th position: 0 ~ 9 10000th position: 0 ~ 3 0 (Fixed) For receiving an NXDN signal $2 $3 $4 $5 ~ $7 XXXXXXXXXXXX $2 Digital squelch (D.SQL) type $2 0X 0 (Fixed) 0 = OFF 1 = RAN $3 Radio Access Number (RAN
  • Icom IC-R8600 | Ci-v Reference Guide - Page 15
    Remote control DDCommand formats (Continued) Memory channel content Command: 1A 00 For receiving a DCR signal $2 $3, $4 $5 $6 ~ $8 XXXXXXXXXXXXXX $2 Digital squelch (D.SQL) type $2 0X 0 (Fixed) 0 = OFF 1 = UC $3, $4 UC code $3 $4 0XXX Once position: 0 ~ 9 10th position: 0 ~ 9 100th position:
  • Icom IC-R8600 | Ci-v Reference Guide - Page 16
    starts from the current frequency 1: Scan starts from the lower edge frequency 0: Does not mute when a signal is received 1: Mutes when a signal is received* 0: Down scan 1: Up scan 0 (Fixed) *If the received signal is wanted, send the command "1A 0B 01" to open the squelch. If the signal is not
  • Icom IC-R8600 | Ci-v Reference Guide - Page 17
    (Continued) Programmable scan start (remote) data (continued) For receiving an NXDN signal @6 @7 @8 @～9 #1 #2 #3 XXXXXXXXXXXXXXXX Memory scan start (remote) data Command: 1A 0B 02 q～t y、u i o～!2 X X ...... X X X X X X X X X X ...... X X @6 Digital squelch (D.SQL) type Refer to "NXDN Digital
  • Icom IC-R8600 | Ci-v Reference Guide - Page 18
    Digital squelch (D.SQL) type ($2)" (p. 12) @2 Digital code squelch (CSQL) code Refer to "Digital code squelch (CSQL) code ($)3 " (p. 12) For receiving a P25 signal @1 @～2 @4 XXXXXXXX @1 Digital squelch (D.SQL) type Refer to "P25 Digital squelch (D.SQL) type ($2)" (p. 12) @2 ~ @4 NAC Refer to "NAC
  • Icom IC-R8600 | Ci-v Reference Guide - Page 19
    Continued) Memory scan start (remote) data (continued) For receiving a DCR signal @1 @2、@3 @4 @～5 @7 XXXXXXXXXXXXXX @1 Digital 0 ~ 9 100 Hz digit: 0 ~ 2 0 (Fixed) LRefer to the IC-R8600 manual for the tone frequencies. DTCS code Command: 1B 02 qwe 0Ｘ0 X X X Once position: 0 ~ 7 10th position: 0 ~ 7
  • Icom IC-R8600 | Ci-v Reference Guide - Page 20
    ) When the last call was finished by a user, "1" is returned. When the audio tone can be heard, "1" is returned. While receiving a BK call, "1" is returned. While receiving an EMR call, "1" is returned. While under an interference (Mode icon D-STAR and FM alternately blink), "1" is returned. While
  • Icom IC-R8600 | Ci-v Reference Guide - Page 21
    0301, 20 0302 ••Data number and description Data number 00 01 02 03 Description D-PRS-Position D-PRS-Object D-PRS-Item D-PRS-Weather - LThe item, that is not contained the received data, is filled with "FF." LFF: N o signal has been received since the power was turned ON. ••GPS/D-PRS data
  • Icom IC-R8600 | Ci-v Reference Guide - Page 22
    $4: Rainfall (Midnight) (0.1 mm steps) $5, $6: Humidity (1% steps) $7 ~ $9: Barometric pressure (0.1 hPa steps) LThe item, that is not contained the received data, is filled with "FF." LFF: N o signal has been received since the power was turned ON GPS/D-PRS message Command: 20 0401, 20 0402
  • Icom IC-R8600 | Ci-v Reference Guide - Page 23
    . (Regardless of NAC) When the last call was finished by a user, "1" is returned. When the audio tone can be heard, "1" is returned. While receiving an emergency call, "1" is returned. While under an interference (Mode icon P25 and FM alternately blink), "1" is returned. When the call is encrypted
  • Icom IC-R8600 | Ci-v Reference Guide - Page 24
    returned. (Regardless of CC or COM ID) bit3 0/1 Last call When the last call was finished by a finisher user, "1" is returned. bit2 0/1 Receiving a When the audio tone can be heard, "1" signal is returned. bit1 0/1 Interfere While under an interference (Mode icon detection dPMR and FM
  • Icom IC-R8600 | Ci-v Reference Guide - Page 25
    in Hexer decimal) !1, !:2 UC (3 digits in decimal) LIf the UC, CALLER or CALLED station is not identified, "FF" is returned. LFF: N o signal has been received since the power was turned ON. DCR RX Status data Command: 20 0D01, 20 0D02 Data Function bit7 0 (Fixed) bit6 0/1 - bit5 0/1 - bit4
  • Icom IC-R8600 | Ci-v Reference Guide - Page 26
    qReceiving mode 00 :LSB 11 :S-AM(D) 01 :USB 14 :S-AM(L) 02 :AM 15 :S-AM(U) 03 :CW 16 :P25 04 :FSK 17 :FSK-R 21 :DCR eFilter setting wData mode 00 : F i x e d eFilter 01 :FIL1 02 :FIL2 03 :FIL3 Scope waveform data Command: 27 00 Outputs the waveform data to the controller. qwerty
  • Icom IC-R8600 | Ci-v Reference Guide - Page 27
    Command: 27 17 0 0XX 00: Hold function OFF 01: Hold function ON 00 (Fixed) Sweep speed settings Command: 27 1A 0 0XX 00: FAST 01: MID 02: SLOW 00 (Fixed) VBW (Video Band Width) settings Command: 27 1D 0 0XX 00 : Narrow 01 : Wide 00 (Fixed) Fixed edge frequency settings Command: 27 1E
  • Icom IC-R8600 | Ci-v Reference Guide - Page 28
    A7375-2EX-3a © 2017-2018 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
CI-V REFERENCE GUIDE
iR8600
COMMUNICATIONS RECEIVER