Icom IC-R8600 Ci-v Reference Guide - Page 7

Remote control DDCommand table (Continued) Cmd. Sub cmd. Data Description 1A 05* 0091 00/01 Send/read the Speech audio output status of [LAN] (00=OFF, 01=ON) 0092 00/01 Send/read the CI-V transceive function setting (00=OFF, 01=ON) 0093 0000 ~ 0223 Send/read the CI-V transceive address (U SB/LAN -> REMOTE) setting (in Hexadecimal) (0000=00h ~ 0223=DFh) 0094 00/01 Send/read the Data Echo Back function for the [USB] (Front) CI-V port (00=OFF, 01=ON) 0095 00/01 Read the CI-V USB (Rear) port setting (00=Connect to [REMOTE], 01=Disconnect from [REMOTE]) (Read only) 0096 00/01 Send/read the Data Echo Back function for the [USB] (Rear) CI-V port (00=OFF, 01=ON) 0097 00/01 Send/read the signal output from [METER] (00=Signal strength, 01=Signal strength and squelch level) 0098 0000 ~ 0255 Send/read the voltage level output from [METER] (0000=0% ~ 0255=100%) 0099 00 ~ 02 Send/read the receiver's reference frequency signal source (00=IN Uses an external reference signal, 01=OFF, 02=Outputs the internal reference signal.) 0100 00/01 Send/read the DHCP function (00=OFF, 01=ON) 0101 00000000 Set the static IP address 00000001 (0000000000000001= 0.0.0.1 ~ ~ 0255025502550254= 255.255.255.254) 02550255 02550254 0102 00000000 Read the dynamic IP address 00000001 (0000000000000001= 0.0.0.1 ~ ~ 0255025502550254= 255.255.255.254) 02550255 (The automatically obtained address (If 02550254 the DHCP is set to ON), or a manually set static IP address.) 0103 01 ~ 30 Send/read the subnet mask to connect to your PC or LAN (01=128.0.0.0 (1 bit) ~ 30=255.255.255.252 (30 bit)) 0104 00000000 Send/read the default gateway setting 00000001 (0000000000000001= 0.0.0.1 ~ ~ 0255025502550254= 255.255.255.254, 02550255 FF (Blank)) 02550254, FF 0105 00000000 Send/read the primary DNS server 00000001 address ~ (0000000000000001= 0.0.0.1 ~ 02550255 0255025502550254= 255.255.255.254, 02550254, FF FF (Blank)) 0106 00000000 Send/read the secondary DNS server 00000001 address ~ (0000000000000001= 0.0.0.1 ~ 02550255 0255025502550254= 255.255.255.254, 02550254, FF FF (Blank)) 0107 See p. 10 Send/read the network name (Up to 15 characters) 0108 00/01 Send/read the network control setting (00=OFF, 01=ON) 0109 00/01 Send/read the Power OFF Setting (for Remote Control) (00=Shutdown only, 01=Standby/Shutdown) 0110 000001 ~ Send/read the UDP port number for the 065535 control signal transfer (1 ~ 65535) 0111 000001 ~ Send/read the UDP port number for the 065535 serial data transfer (1 ~ 65535) 0112 000001 ~ Send/read the UDP port number for the 065535 audio signal transfer (1 ~ 65535) 0113 00/01 Send/read the internet access line (00=FTTH, 01=ADSL/CATV) 0114 See p. 10 Send/read the nickname of the IC-R8600 (1 ~ 16 characters) 0115 0000 ~ 0255 Send/read the LCD backlight brightness (0000=0% ~ 0255=100%) 6 Cmd. Sub cmd. 1A 05* 0116 0117 0118 0119 0120 0121 0122 0123 0124 0125 0126 0127 0128 0129 0130 0131 0132 0133 0134 0135 0136 0137 0138 0139 0140 0141 0142 Data 0000 ~ 0255 00/01 00/01 00/01 00/01 00/01 00/01 00/01 00 ~ 03 00/01 00 ~ 03 00/01 p.10 00/01 00/01 20000101 ~ 20991231 0000 ~ 2359 00/01 See p. 10 See p. 10 00 ~ 02 00 ~ 02 00/01 00/01 00 ~ 03 00/01 See p. 10 Description Send/read the LED brightness (0000=0% ~ 0255=100%) Send/read the display background type (00=A, 01=B) Send/read the Meter Peak Hold function (00=OFF, 01=ON) Send/read the Memory name display (00=OFF, 01=ON) Send/read the group name display function (00=OFF, 01=ON The group name is displayed when you change the memory channel group) Send/read the Notch filter width display function (00=OFF, 01=ON T he filter width is displayed when you select the Manual Notch.) Send/read the digital TWIN PBT shift value display function (00=OFF, 01=ON The shift value is displayed while rotating [DIAL C].) Send/read the digital IF filter width and shift value display function (00=OFF, 01=ON The filter width and shift value are displayed when you change the IF filter.) Send/read the digital signal information display function (00=OFF, 01=Normal, 02=RX Hold, 03=Hold) Send/read the P25 ID display type (00=Decimal, 01=Hexadecimal) Send/read the Screen Saver activation time (0 0=OFF, 01=15 minutes, 02=30 minutes, 03=60 minutes) Send/read the opening message display function (00=OFF, 01=ON) Send/read the opening comment (Up to 10 characters) Send/read the display language (00=English, 01=Japanese) Send/read the system language (00=English, 01=Japanese) Send/read the date (Year/Month/Day) (20000101 "2000/1/1" ~ 20991231 "2099/12/31") Send/read the current time (0000 "00:00" ~ 2359 "23:59") Send/read the NTP function (00=OFF, 01=ON) Send/read the NTP server address (Up to 64 characters) Send/read the UTC offset time (-14:00 ~ +14:00 (in 5 minutes steps)) Send/read the scope peak level holding function (00=OFF, 01=10 seconds Hold, 02=ON) Send/read the scope center position (00=Filter Center, 01=Carrier Point Center, 02=Carrier Point Center (with absolute frequency)) (Only in the Center mode) Send/read the scope marker position (00=Filter Center, 01=Carrier Point) (Only in the Fixed mode) Send/read the scope Video Band Width (VBW) (00=Narrow, 01=Wide) Send/read the FFT scope waveform averaging function (00=OFF, 01=2, 02=3, 03=4) Send/read the scope outline waveform display (00=Fill, 01=Fill+Line) Send/read the scope waveform (current) color