Icom IC-R8600 Ci-v Reference Guide - Page 9

Remote control DDCommand table (Continued) Cmd. Sub cmd. Data Description Cmd. Sub cmd. Data Description 1C* 02 00/01 Send/read the Monitor function 26* See p. 25 Send/read the selected or not selected (00=OFF, 01=ON) VFO's operating mode and filter 1D* 00 00/02 Send/read the REMOTE function setting 27* 00 See p. 25 Read the Scope waveform data 20 00 00* 01 00/01 See p. 19 (00=OFF, 02=ON) Send/read the D-STAR Call sign output setting (00=Transceive OFF, 01=Transceive ON) Output the D-STAR Call sign setting for transceive 10 00/01 Send/read the Scope ON/OFF status (00=OFF, 01=ON) 11*2 00/01 Send/read the Scope wave data output setting (00=OFF, 01=ON) 02 See p. 19 Read the D-STAR Call sign contained in 12 00 Send/read the Scope MAIN/SUB setting the received signal (00=Fixed to MAIN) 01 00* 01 00/01 See p. 19 Send/read the D-STAR message output setting (00=Transceive OFF, 01=Transceive ON) Output the D-STAR message for transceive 13 00 Send/read the Scope Single/Dual setting (00=Fixed to Single) 14 See p. 26 Send/read the Scope Center mode or Fixed mode setting 02 See p. 19 Read the D-STAR message contained in the received signal 02 00* 00/01 Send/read the D-STAR RX status output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 19 Output the D-STAR RX status for transceive 02 See p. 19 Read the D-STAR RX status 03 00* 00/01 Send/read the D-STAR RX GPS/D-PRS data output setting (00=Transceive OFF, 01=Transceive ON) 01 See pp. 20 ~ 21 Output the D-STAR RX GPS/D-PRS data for transceive 02 See pp. 20 ~ 21 Read the D-STAR RX GPS/D-PRS data 04 00* 00/01 Send/read the D-STAR RX GPS/D-PRS message output setting 15 See p. 26 17 See p. 26 19 See p. 26 1A See p. 26 1C 00 ~ 02 1D See p. 26 1E See p. 26 *(Asterisk) Send/read data Send/read the span setting in the Center mode Scope Send/read the Scope hold function status Send/read the Scope Reference level Send/read the Sweep speed Send/read scope center frequency setting in the Center mode (00=Filter Center, 01=Carrier Point Center, 02=Carrier Point Center (Abs. Freq.)) Send/read the Scope VBW setting Send/read the Scope Fixed edge frequencies 01 02 05 00* See p. 21 See p. 21 00/01 (00=Transceive OFF, 01=Transceive ON) Output the D-STAR RX GPS/D-PRS message for transceive Read the D-STAR RX GPS/D-PRS message Send/read the D-STAR RX CSQL code *1 When sending the power ON command (18 01), you need to repeatedly send "FE" before the standard format. The following is the approximate number of needed repetition. • 115200 bps: 119 "FE"s output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 22 Output the D-STAR RX CSQL code for transceive • 57600 bps: 59 "FE"s • 38400 bps: 40 "FE"s • 19200 bps: 20 "FE"s 02 06 00* 01 See p. 22 00/01 See p. 22 Read the D-STAR RX CSQL code Send/read the P25 ID output setting (00=Transceive OFF, 01=Transceive ON) Output the P25 ID for transceive • 9600 bps: 9 "FE"s • 4800 bps: 5 "FE"s Example: When using 4800 bps 02 20 07 00* See p. 22 Read the P25 ID 00/01 Send/read the P25 RX status output Preamble R8600's Controller's Command Sub Post address address command amble setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 22 Output the P25 RX status for transceive FE FEFE9 6E0 1 8 0 1 FD ×5 02 08 00* 01 02 09 00* See p. 22 00/01 See p. 22 See p. 22 00/01 Read the P25 RX status Send/read the dPMR RX ID output setting (00=Transceive OFF, 01=Transceive ON) Output the dPMR RX ID for transceive Read the dPMR RX ID Send/read the dPMR RX status output *2 W hen you use the [USB (Front)] port, you need to select "115200" in the "CI-V Baud Rate" item. When you use the [USB (Rear)] port, you need to select "Unlink from [REMOTE]" in the "CI-V USB port" item, and need to select "115200" in the "CI-V Baud Rate" item. setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 23 Output the dPMR RX status for transceive 02 See p. 23 Read the dPMR RX status You can use the [LAN] port regardless of those settings. You cannot use the [REMOTE] terminal regardless of those settings. 0A 00* 00/01 Send/read the NXDN RX ID output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 23 Output the NXDN RX ID for transceive 02 See p. 23 Read the NXDN RX ID 0B 00* 00/01 Send/read the NXDN RX status output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 23 Output the NXDN RX status for transceive 02 See p. 23 Read the NXDN RX status 0C 00* 00/01 Send/read the DCR RX ID output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 24 Output the DCR RX ID for transceive 02 See p. 24 Read the DCR RX ID 0D 00* 00/01 Send/read the DCR RX status output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 24 Output the DCR RX status for transceive 02 See p. 24 Read the DCR RX status 22 01 00* 00/01 Send/read the D-STAR RX data output setting (00=Transceive OFF, 01=Transceive ON) 01 See p. 24 Output the D-STAR RX data for transceive 25* See p. 24 Send/read the selected or not selected VFO frequency 8