Insignia NS-FWM45W3 User Guide - Page 42

No power. My, itself. It may take up to two minutes

Get Insignia NS-FWM45W3 PDF manuals and user guides View all Insignia NS-FWM45W3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

USER MAINTENANCE INSTRUCTIONS PROBLEM POSSIBLE CAUSE SOLUTION The cabinet is moving. • Your washer is designed to move 1/4 in. (6.35 mm) to reduce forces transmitted to the floor. This movement is normal. My washer is making a loud or unusual noise, vibration, or shaking. All the leveling legs are not firmly touching the floor. The load is unbalanced. • Push and pull on the back right and then back left of your washer to make sure that it is level. If your washer is uneven, adjust the leveling legs so they are all firmly touching the floor and locked in place. • Open the door and manually redistribute the load. To check your washer, run Rinse & Spin with no load. If it runs normally, the unbalance was caused by the load. The pump is clogged. • See Cleaning the pump filter on page 36 on how to clean the pump filter. Your washer is unplugged. • Make sure that the power cord is plugged securely into a working outlet. No power. My washer is not working or is dead. The water supply is turned off. The circuit breaker or fuse is tripped or blown. • Turn the water faucets fully on. • Check the house circuit breakers or fuses. Replace fuses or reset the breaker. Your washer should have a separate outlet. Your washer is performing an automatic self system checks • The first time your washer is plugged in, it automatically checks itself. It may take up to two minutes before you can use your washer. This is normal. Your washer is overloaded. • The dry weight of the load should be less than 18 lbs. My clothes have snags, holes, tears, rips or excessive Pens, pencils, nails, screws or other objects were left in pockets. wear. Snaps, hooks, sharp buttons, belt buckles, and zippers were left unsecured. • Remove loose items from pockets. • Fasten snaps, hooks, buttons, and zippers. The time This is normal. remaining for the spin cycle is wrong or changes. • During the spin cycle, your washer may need to re-balance the load to reduce vibrations. When this occurs, the estimated time is increased. 42 www.insigniaproducts.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
USER MAINTENANCE INSTRUCTIONS
42
www.insigniaproducts.com
My washer is
making a loud or
unusual noise,
vibration, or
shaking.
The cabinet is moving.
•
Your washer is designed to move
1/4 in. (6.35 mm) to reduce forces
transmitted to the floor. This
movement is normal.
All the leveling legs are
not firmly touching the
floor.
•
Push and pull on the back right and
then back left of your washer to
make sure that it is level. If your
washer is uneven, adjust the
leveling legs so they are all firmly
touching the floor and locked in
place.
The load is unbalanced.
•
Open the door and manually
redistribute the load. To check your
washer, run
Rinse & Spin
with no
load. If it runs normally, the
unbalance was caused by the load.
The pump is clogged.
•
See Cleaning the pump filter
on
page 36
on how to clean the pump
filter.
No power. My
washer is not
working or is
dead.
Your washer is unplugged.
•
Make sure that the power cord is
plugged securely into a working
outlet.
The water supply is turned
off.
•
Turn the water faucets fully on.
The circuit breaker or fuse
is tripped or blown.
•
Check the house circuit breakers or
fuses. Replace fuses or reset the
breaker. Your washer should have a
separate outlet.
Your washer is performing
an automatic self system
checks
•
The first time your washer is
plugged in, it automatically checks
itself. It may take up to two minutes
before you can use your washer.
This is normal.
My clothes have
snags, holes, tears,
rips or excessive
wear.
Your washer is overloaded.
•
The dry weight of the load should
be less than 18 lbs.
Pens, pencils, nails, screws
or other objects were left
in pockets.
•
Remove loose items from pockets.
Snaps, hooks, sharp
buttons, belt buckles, and
zippers were left
unsecured.
•
Fasten snaps, hooks, buttons, and
zippers.
The time
remaining for the
spin cycle is
wrong or changes.
This is normal.
•
During the spin cycle, your washer
may need to re-balance the load to
reduce vibrations. When this
occurs, the estimated time is
increased.
PROBLEM
POSSIBLE CAUSE
SOLUTION