Intel D845HV Product Guide - Page 33

RM A to the AGP connector B

Get Intel D845HV PDF manuals and user guides View all Intel D845HV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Installing and Replacing Desktop Board Components The AGP card RM (see Figure 13) encloses the board's AGP connector and stabilizes the AGP card. Place the board (component side up) on a flat, supportive surface, preferably on the anti-static bag in which the board was shipped. Follow the steps outlined below to attach the RM (A) to the AGP connector (B): 1. Locate the AGP connector (J5E1) on the board as shown below. Note that the board's silkscreen (C) indicates the correct final position of the lever (D) on the RM. A D E C B OM11980 Figure 13. Installing the AGP Card Retention Mechanism 2. Position the RM over the AGP connector as shown below. OM10111 3. Push the lever end of the RM in the direction of the arrow until the two rearmost tabs (E) spread over the end of the AGP connector. OM10180 4. Push the free end of the RM over the other end of the AGP connector and press down evenly on both ends of the RM until all four tabs click underneath the AGP connector. Do not apply unnecessary pressure to avoid damaging the board. OM10181 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Installing and Replacing Desktop Board Components
33
The AGP card RM (see Figure 13) encloses the board’s AGP connector and stabilizes the AGP
card.
Place the board (component side up) on a flat, supportive surface, preferably on the
anti-static bag in which the board was shipped.
Follow the steps outlined below to attach the
RM (A) to the AGP connector (B):
1.
Locate the AGP connector (J5E1) on the board as shown below.
Note that the board’s
silkscreen (C) indicates the correct final position of the lever (D) on the RM.
OM11980
C
B
A
E
D
Figure 13.
Installing the AGP Card Retention Mechanism
2.
Position the RM over the AGP connector as shown below.
OM10111
3.
Push the lever end of the RM in the direction of the arrow until the two rearmost tabs (E)
spread over the end of the AGP connector.
OM10180
4.
Push the free end of the RM over the other end of the AGP connector and press down evenly
on both ends of the RM until all four tabs click underneath the AGP connector.
Do not apply
unnecessary pressure to avoid damaging the board.
OM10181