Intel DZ68BC Product Guide - Page 66

Installing the WiFi/Bluetooth* Module in a Desktop Chassis (Optional - wireless

Get Intel DZ68BC PDF manuals and user guides View all Intel DZ68BC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Intel Desktop Board DZ68BC Product Guide Installing the WiFi/Bluetooth* Module in a Desktop Chassis (Optional) Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board DZ68BC in your desktop system allows you to connect to wireless networks and Bluetooth peripherals. The recommended installation procedure for a typical desktop chassis is as follows: 1. Observe the precautions in "Before You Begin" on page 31. 2. Make sure that the system is turned off and disconnected from its power source. 3. Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel (Figure 30, A). 4. Remove the metal filler plate from the internal drive bay (Figure 30, B). 5. Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth Module and attach the module to the back side of the plastic drive bay cover (Figure 30, C). 6. Connect one end of the USB cable to the connector on the front of the module (Figure 30, D). 7. Reinstall the plastic drive bay cover in the chassis bezel while routing the USB cable into the chassis through the empty drive bay (Figure 30, E). 8. Connect the free end of the USB cable to an unused front panel USB header on the Desktop Board (see Figure 1, HH for locations) (Figure 30, F). Figure 30. Installing the WiFi/Bluetooth Module 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Intel Desktop Board DZ68BC Product Guide
66
Installing the WiFi/Bluetooth* Module in a
Desktop Chassis (Optional)
Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board DZ68BC
in your desktop system allows you to connect to wireless networks and Bluetooth
peripherals.
The recommended installation procedure for a typical desktop chassis is as follows:
1.
Observe the precautions in "Before You Begin" on page 31.
2.
Make sure that the system is turned off and disconnected from its power source.
3.
Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel
(Figure 30, A).
4.
Remove the metal filler plate from the internal drive bay (Figure 30, B).
5.
Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth
Module and attach the module to the back side of the plastic drive bay cover
(Figure 30, C).
6.
Connect one end of the USB cable to the connector on the front of the module
(Figure 30, D).
7.
Reinstall the plastic drive bay cover in the chassis bezel while routing the USB
cable into the chassis through the empty drive bay (Figure 30, E).
8.
Connect the free end of the USB cable to an unused front panel USB header on the
Desktop Board (see Figure 1, HH for locations) (Figure 30, F).
Figure 30.
Installing the WiFi/Bluetooth Module