Intel SBXD62 User Guide - Page 27

Removing the Blade Server from an Intel® Blade Server Chassis SBCE, Blade Server Chassis SBCE.

Get Intel SBXD62 - Server Compute Blade PDF manuals and user guides
UPC - 735858185448
View all Intel SBXD62 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Removing the Blade Server from an Intel® Blade Server Chassis SBCE The following illustration shows how to remove the blade server from a typical Intel® Blade Server Chassis SBCE. AF000440 Important: • To maintain proper system cooling, do not operate the Intel® Blade Server Chassis SBCE without a blade server, or filler blade installed in each blade bay. • Note the bay number. Reinstalling a blade server into a different bay than the one from which it was removed could have unintended consequences. Some configuration information and update options are established according to bay number; if you reinstall the blade server into a different bay, you might need to reconfigure the blade server. To remove the blade server, complete the following steps: 1. If the blade server is operating, shut down the operating system; then, press the power-control button (behind the blade server control panel door) to turn off the blade server (see "Turning off the Blade Server" on page 7 for more information). Important: Wait at least 30 seconds, until the hard disk drives stop spinning, before proceeding to the next step. 2. Open the two release handles as shown in the illustration. The blade server moves out of the bay approximately 0.6 cm (0.25 inch). 3. Pull the blade server out of the bay. Spring-loaded doors further back in the bay move into place to cover the bay temporarily. 4. Place either a filler blade or another blade in the bay within 1 minute. The recessed spring-loaded doors will move out of the way as you insert the blade or filler blade. Intel® Server Compute Blade SBXD62 Installation and User's Guide 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Intel® Server Compute Blade SBXD62 Installation and User’s Guide
17
Removing the Blade Server from an Intel® Blade Server
Chassis SBCE
The following illustration shows how to remove the blade server from a typical Intel®
Blade Server Chassis SBCE.
Important:
•
To maintain proper system cooling, do not operate the Intel® Blade Server Chassis
SBCE without a blade server, or filler blade installed in each blade bay.
•
Note the bay number. Reinstalling a blade server into a different bay than the one
from which it was removed could have unintended consequences. Some configuration
information and update options are established according to bay number; if you
reinstall the blade server into a different bay, you might need to reconfigure the blade
server.
To remove the blade server, complete the following steps:
1.
If the blade server is operating, shut down the operating system; then, press the
power-control button (behind the blade server control panel door) to turn off the blade
server (see
“Turning off the Blade Server” on page 7
for more information).
Important:
Wait at least 30 seconds, until the hard disk drives stop spinning, before proceeding to the
next step.
2.
Open the two release handles as shown in the illustration. The blade server moves out
of the bay approximately 0.6 cm (0.25 inch).
3.
Pull the blade server out of the bay. Spring-loaded doors further back in the bay move
into place to cover the bay temporarily.
4.
Place either a filler blade or another blade in the bay within 1 minute. The recessed
spring-loaded doors will move out of the way as you insert the blade or filler blade.
AF000440