Invacare CRFTI Owners Manual - Page 59

Converting Wheel Lock From Push-to-Lock to Pull-to-Lock or Pull-to-Lock to Push-to-Lock

Get Invacare CRFTI PDF manuals and user guides View all Invacare CRFTI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

SECTION 9-WHEEL LOCKS Converting Wheel Lock From Push-to-Lock to Pull-to-Lock or Pull-to-Lock to Push-to-Lock NOTE: For this procedure, refer to FIGURE 9.3. Converting From Push-to-Lock to Pull-to-Lock 1. Remove set screw from the lower stop position (Detail "A"). NOTE: As the wheel lock handle is pushed downwards, the wheel lock will engage and then disengage the wheel. 2. Push wheel lock handle down to access the upper stop position (Detail "B"). 3. Install set screw into upper stop position. 4. Pull wheel lock handle up to engage wheel lock. If wheel lock does not properly engage the wheel, refer to Adjusting the Wheel Lock on page 57. Converting From Pull-to-Lock to Push-to-Lock 1. Remove set screw from the upper stop position (Detail "B"). NOTE: As the wheel lock handle is pulled upwards, the wheel lock will engage and then disengage the wheel. 2. Pull wheel lock handle up to access the lower stop position (Detail "A"). 3. Install set screw into lower stop position. 4. Push wheel lock handle down to engage wheel lock. If wheel lock does not properly engage the wheel, refer to Adjusting the Wheel Lock on page 57. DETAIL "A" WHEEL LOCK IN PUSH-TO-LOCK CONFIGURATION Wheel Lock Handle DETAIL "B" WHEEL LOCK IN PULL-TO-LOCK CONFIGURATION Set Screw (in Upper Stop Position) Set Screw (in Lower Stop Position) Wheel Lock Handle FIGURE 9.3 Converting Wheel Lock From Push-to-Lock to Pull-to-Lock or Pull-to-Lock to Push-to-Lock Part No 1134872 59 Crossfire™Series Wheelchairs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
SECTION 9—WHEEL LOCKS
Part No 1134872
59
Crossfire
™
Series Wheelchairs
Converting Wheel Lock From Push-to-Lock to
Pull-to-Lock or Pull-to-Lock to Push-to-Lock
NOTE: For this procedure, refer to FIGURE 9.3.
Converting From Push-to-Lock to Pull-to-Lock
1.
Remove set screw from the lower stop position (Detail “A”).
NOTE: As the wheel lock handle is pushed downwards, the wheel lock will engage and then
disengage the wheel.
2.
Push wheel lock handle down to access the upper stop position (Detail “B”).
3.
Install set screw into upper stop position.
4.
Pull wheel lock handle up to engage wheel lock. If wheel lock does not properly
engage the wheel, refer to Adjusting the Wheel Lock
on page 57.
Converting From Pull-to-Lock to Push-to-Lock
1.
Remove set screw from the upper stop position (Detail “B”).
NOTE: As the wheel lock handle is pulled upwards, the wheel lock will engage and then disengage
the wheel.
2.
Pull wheel lock handle up to access the lower stop position (Detail “A”).
3.
Install set screw into lower stop position.
4.
Push wheel lock handle down to engage wheel lock. If wheel lock does not properly
engage the wheel, refer to Adjusting the Wheel Lock
on page 57.
FIGURE 9.3
Converting Wheel Lock From Push-to-Lock to Pull-to-Lock or Pull-to-Lock to
Push-to-Lock
DETAIL “A” WHEEL LOCK IN
PUSH-TO-LOCK CONFIGURATION
Set Screw
(in Lower Stop Position)
Wheel Lock
Handle
DETAIL “B” WHEEL LOCK IN
PULL-TO-LOCK CONFIGURATION
Set Screw
(in Upper Stop Position)
Wheel Lock
Handle