Invacare TDXSP2V Owners Manual - Page 44

WARNING, Risk of short circuit and electric shock if the, battery charger has been damaged, Risk

Get Invacare TDXSP2V PDF manuals and user guides View all Invacare TDXSP2V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Invacare® TDX® SP2 Series WARNING! Risk of short circuit and electric shock if the battery charger has been damaged - Do not use the battery charger if it has been dropped or damaged. WARNING! Risk of Injury, Damage or Death Improper routing of cord(s) may cause tripping, entanglement or strangulation hazard that may result in injury, damage or death. - Ensure all cord(s) are routed and positioned properly while charging. - Avoid positioning cord(s) across areas of high foot traffic (i.e. aisles, doorways, hallways, etc.) while charging. - Close supervision and attention is needed when operating the wheelchair near children, pets or people with physical/mental disabilities. 1. Perform one of the following • Charging NEW batteries-Ensure the mobility device power is ON. The wheelchair power must be on to ensure that accurate battery charge levels display on the remote. New batteries must be charged fully. This includes on initial delivery and after battery replacement. The Battery Synchronization Procedure MUST be performed within 24 hours of powering on the wheelchair. The Battery Synchronization Procedure can be found in the LiNX service manual and must be performed by a provider or qualified technician. • Charging existing batteries-Switch off the mobility device. 2. Connect the battery charger to the charger socket. The charger connector pins are identified in the following ways: Fig. 7-1 • Pin 1 A - Battery Plus (+) • Pin 2 B - Battery (-) • Pin 3 C - Inhibit 3. Connect the battery charger to the power supply. 44 60101877-B

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Invacare® TDX® SP2 Series
WARNING!
Risk of short circuit and electric shock if the
battery charger has been damaged
– Do not use the battery charger if it has been
dropped or damaged.
WARNING!
Risk of Injury, Damage or Death
Improper routing of cord(s) may cause tripping,
entanglement or strangulation hazard that may
result in injury, damage or death.
– Ensure all cord(s) are routed and positioned
properly while charging.
– Avoid positioning cord(s) across areas of high
foot traffic (i.e. aisles, doorways, hallways, etc.)
while charging.
– Close supervision and attention is needed when
operating the wheelchair near children, pets or
people with physical/mental disabilities.
1.
Perform one of the following
•
Charging NEW batteries—Ensure the mobility
device power is ON.
The wheelchair power must be on to
ensure that accurate battery charge levels
display on the remote. New batteries must
be charged fully. This includes on initial
delivery and after battery replacement. The
Battery Synchronization Procedure MUST be
performed within 24 hours of powering on
the wheelchair. The Battery Synchronization
Procedure can be found in the LiNX service
manual and must be performed by a
provider or qualified technician.
•
Charging existing batteries—Switch off the mobility
device.
2.
Connect the battery charger to the charger socket.
The charger connector pins are identified in the
following ways:
Fig. 7-1
•
Pin 1
A
— Battery Plus (+)
•
Pin 2
B
— Battery (-)
•
Pin 3
C
— Inhibit
3.
Connect the battery charger to the power supply.
44
60101877-B