Jenn-Air JGS9900CDS Installation Instruction - Page 10

Install Anti-Tip Bracket, Install Downdraft System - installation instructions

Get Jenn-Air JGS9900CDS PDF manuals and user guides View all Jenn-Air JGS9900CDS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Install Anti-Tip Bracket WARNING 4. Drill two ¹⁄₈" (3.0 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations. Floor Mounting Wall Mounting A B A B Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved. Do not operate range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults. 1. Remove the anti-tip bracket that is taped to the package containing literature. 2. Determine which mounting method to use: floor or wall. If you have a stone or masonry floor, you can use the wall mounting method. 3. Determine and mark centerline of the cutout space. The mounting bracket can be installed on either the left side or right side of the cutout. Position mounting bracket in cutout so that right (or left) edge of the bracket is 14¹⁄₄" (36.2 cm) from centerline, as shown. A A. #12 x 1⁵⁄₈" screws B. Anti-tip bracket A. #12 x 1⁵⁄₈" screws B. Anti-tip bracket 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1⁵⁄₈" screws provided. Install Downdraft System Determine Equivalent Length of Vent System This range is equipped with a dual range blower. It is shipped from the factory for Low Range installations. If vent system equivalent length exceeds 30 ft (9.1 m), the downdraft blower motor must be converted to High Range for best performance. See "Calculating Vent System Length" section. To Convert: Gently remove the spring loaded Restricter Ring from the blower inlet by pressing on one of the 3 springs. B A. Centerline B. 14¹⁄₄" (36.2 cm) B A A. Restricter ring B. Spring Determine which venting method to use: floor, rear wall, or left side venting. Go to the section for your type of venting. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
10
Install Anti-Tip Bracket
1.
Remove the anti-tip bracket that is taped to the package
containing literature.
2.
Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the wall
mounting method.
3.
Determine and mark centerline of the cutout space. The
mounting bracket can be installed on either the left side or
right side of the cutout. Position mounting bracket in cutout
so that right (or left) edge of the bracket is 14
¹⁄₄
" (36.2 cm)
from centerline, as shown.
4.
Drill two
¹⁄₈
" (3.0 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
5.
Using the Phillips screwdriver, mount anti-tip bracket to the
wall or floor with the two #12 x 1
⁵⁄₈
" screws provided.
Install Downdraft System
Determine Equivalent Length of Vent System
This range is equipped with a dual range blower. It is shipped
from the factory for Low Range installations. If vent system
equivalent length exceeds 30 ft (9.1 m), the downdraft blower
motor must be converted to High Range for best performance.
See “Calculating Vent System Length” section.
To Convert:
Gently remove the spring loaded Restricter Ring from the blower
inlet by pressing on one of the 3 springs.
Determine which venting method to use: floor, rear wall, or left
side venting. Go to the section for your type of venting.
A. Centerline
B. 14
¹⁄₄
" (36.2 cm)
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
Floor Mounting
Wall Mounting
A. #12 x 1
⁵⁄₈
" screws
B. Anti-tip bracket
A. #12 x 1
⁵⁄₈
" screws
B. Anti-tip bracket
A. Restricter ring
B. Spring
A
B
A
B
A
B