Kenmore 75062 Owners Manual - Page 5

Exteri°r - weight

Get Kenmore 75062 - 6,000 BTU Single Room Air Conditioner PDF manuals and user guides View all Kenmore 75062 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

INSTALLATION REQUIREMENTS To avoid installation difficulties, read instructions completely before starting. This publication contains important information for the installation and operation of your room air conditioner. Your air conditioner will install into standard double hung windows with actual clear opening widths of 26 to 39-3/8 inches (660ram to 1000ram) (FIG. 1). Lower sash must open sufficiently to allow a clear vertical opening of 12 inches (305mm). However, some window frame design variations require modification to the window for safe, proper installation. Side louvers and the rear of the air conditioner must have clear air space to allow enough airflow through the condenser for heat removal. The rear of the unit must be outdoors, not inside a building or garage. 1 1 _._t 26_(660mm_)to t _39/8'1(1000mm) I112"(30ra5inmm) I I _ Window J I Inner s__ :;] Interior wall " SillOffset ExtFeIGr.i°1r ELECTRICAL SERVICE Check your available electrical service. The power supply available must be the same as that shown on the unit nameplate (found on left side of front grille). All models are equipped with a 3-prong service plug to provide proper service and safe positive grounding. Do not change plug in any way. Do not use an adapter plug. if your present wall outlet does not match your plug, call a qualified electrician to make the necessary corrections. SAVE CARTON and this OWNER'S MANUAL for future reference. The carton is the best way to store unit during winter or when not in use. INSTALLATION HARDWARE ITEM A B C D E F G H NAME OF PARTS SUPPORT, BRACKET LEVELING BOLT LEVELING BOLT SCREW: 5/8" SCREW: 5/8" FOAM SEAL FOAM STRIP L BRACKET REQUIRED TOOLS: Tight Fitting gloves Standard screwdriver Phillips screwdriver Pencil Sharp knife Tape measure Electric drill 1/4-inch drill bit Q'TY 1 1 1 2 5 1 1 1 To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: • Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. • Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. • Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. • Make sure air conditioner does not fall during instaNation. / IG 2 -5-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
INSTALLATION
REQUIREMENTS
To
avoid
installation
difficulties,
read
instructions
completely
before
starting.
This
publication
contains
important
information
for the
installation
and
operation
of your
room
air
conditioner.
Your
air
conditioner
will
install
into
standard
double
hung
windows
with
actual
clear
opening
widths
of 26 to
39-3/8
inches
(660ram
to
1000ram)
(FIG.
1).
Lower
sash
must
open
sufficiently
to allow
a clear
vertical
opening
of
12 inches
(305mm).
However,
some
window
frame
design
variations
require
modification
to the
window
for
safe,
proper
installation.
Side
louvers
and
the
rear
of the
air
conditioner
must
have
clear
air
space
to allow
enough
airflow
through
the
condenser
for heat
removal.
The
rear
of the
unit
must
be outdoors,
not
inside
a building
or garage.
_._t
26_(660mm)to
_
t
_39/8'1(1000mm)
11
I112"(305mm)
rain
I
I
_
Window
J
I
Inner s__
SillOffset
:;]
Exteri°r
Interior wall
"
FIG.
1
ELECTRICAL
SERVICE
Check
your
available
electrical
service.
The
power
supply
available
must
be the
same
as that
shown
on
the
unit
nameplate
(found
on left side
of front
grille).
All
models
are
equipped
with
a 3-prong
service
plug
to
provide
proper
service
and
safe
positive
grounding.
Do
not change
plug
in any
way.
Do
not
use
an adapter
plug.
if your
present
wall
outlet
does
not
match
your
plug,
call
a qualified
electrician
to
make
the
necessary
corrections.
SAVE
CARTON
and
this
OWNER'S
MANUAL
for
future
reference.
The
carton
is the
best
way
to store
unit during
winter
or
when
not
in use.
INSTALLATION
HARDWARE
ITEM
NAME OF PARTS
Q'TY
A
SUPPORT,
BRACKET
1
B
LEVELING
BOLT
1
C
LEVELING
BOLT
1
D
SCREW:
5/8"
2
E
SCREW:
5/8"
5
F
FOAM SEAL
1
G
FOAM STRIP
1
H
L BRACKET
1
REQUIRED
TOOLS:
Tight
Fitting
gloves
Standard
screwdriver
Phillips
screwdriver
Pencil
Sharp
knife
Tape
measure
Electric
drill
1/4-inch
drill
bit
To avoid risk of personal injury, property damage,
or product damage due to the weight of this
device and sharp edges that may be exposed:
• Air conditioners covered in this manual pose an
excessive weight hazard. Two or more people
are needed to move and install the unit.
To prevent injury or strain, use proper lifting and
carrying techniques when moving unit.
• Carefully inspect location where air conditioner
will be installed. Be sure it will support the
weight of the unit over an extended period of
time.
• Handle air conditioner with care.
Wear protective gloves whenever lifting or
carrying the unit. AVOID the sharp metal fins of
front and rear coils.
• Make sure air conditioner does not fall during
instaNation.
/
IG
2
-5-