Kenmore 75062 Owners Manual - Page 6

Installation, How To Install - window air conditioner

Get Kenmore 75062 - 6,000 BTU Single Room Air Conditioner PDF manuals and user guides View all Kenmore 75062 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

INSTALLATION To avoid the possibiity of personal injury, unplug power to unit before installing or servicing. Carefully remove air conditioner from carton, check for possible shipping damage. Pick a location which will allow you to blow the cold air into the area you want. Windows used for installation must be strong enough to support the weight of the air conditioner. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed. When cooling more than one room, installation location is very important. To cool your rooms, cold air must be blown from the air conditioner in a straight path. If air conditioner is blocked by a storm window frame, see Step 7 and 8 on Page 8 before beginning to install. HOW TO INSTALL _lCut the FOAM STRIP (ITEM G) to fit the underside of the window sash. Open the window, peel off the backing and attach the FOAM STRIP as shown in FIG. 3. FOAM STRIP (ITEM G) FIG. 3 F_Mark center line with pencil on the center of the inner sill, as shown in FIG. 4 I_ Install support bracket on window. See FIG. 5. Install leveling bolt up through bottom side of support bracket. You can choose a short bolt (ITEM C) or a long one (ITEM B) according to window type. Also, you should select the position of hole on bracket. Position bracket on sill 1 inch (25.4mm) to left of center line of window (See FIG. 5). Fasten bracket loosely to sill with screws (ITEM D) provided. Adjust leveling bolt so that the air conditioner will be installed with a very slight tilt (about 1/4") downward toward the outside for proper drainage. Tighten bracket screws. SCREW (ITEM D) INNER WINDOW SILL 1"(25.4mrr " CENTER LINE OF WINDOW _ FIG. 5 SCREW INNERSiLL SUPPORT BRACKET ABOUT1/4" __------_ PLEVELING f _'_ BOL_uTERfILL INDOOR II't 'lJ /I I OUTDOOR FIG. 6 iNDOOR CENTERLINE INNERSILL FIG. 4 Failure to securely install support bracket may result in unit falling from window if window sash is raised after unit is installed. This could result in personal injury. -6-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
INSTALLATION
To avoid the possibiity of personal injury, unplug
power to unit before installing or servicing.
Carefully
remove
air conditioner
from
carton,
check
for possible
shipping
damage.
Pick
a location
which
will
allow
you
to blow
the
cold
air
into
the
area
you
want.
Windows
used
for installation
must
be strong
enough
to
support
the
weight
of the
air conditioner.
Good
installation
with
special
attention
to the
proper
position
of
the
unit will
lessen
the
chance
that
service
will
be
needed.
When
cooling
more
than
one
room,
installation
location
is very
important.
To
cool
your
rooms,
cold
air
must
be blown
from
the
air conditioner
in a
straight
path.
If air conditioner
is blocked
by a storm
window
frame,
see
Step
7 and
8 on
Page
8 before
beginning
to install.
HOW TO INSTALL
_lCut
the
FOAM
STRIP
(ITEM
G) to fit the
underside
of the
window
sash.
Open
the
window,
peel
off the
backing
and
attach
the
FOAM
STRIP
as
shown
in FIG.
3.
FOAM STRIP
(ITEM G)
FIG. 3
F_Mark
center
line
with
pencil
on the
center
of the
inner
sill,
as
shown
in FIG.
4
iNDOOR
CENTERLINE
INNERSILL
FIG.
4
I_
Install
support
bracket
on window.
See
FIG.
5.
Install
leveling
bolt up through
bottom
side
of support
bracket.
You
can choose
a short
bolt (ITEM
C) or a
long one
(ITEM
B) according
to window
type.
Also,
you
should
select
the
position
of hole
on bracket.
Position
bracket
on sill 1 inch
(25.4mm)
to left of
center
line of window
(See
FIG.
5).
Fasten
bracket
loosely
to sill with
screws
(ITEM
D)
provided.
Adjust
leveling
bolt so that
the air conditioner
will
be
installed
with
a very slight
tilt (about
1/4") downward
toward
the
outside
for proper
drainage.
Tighten
bracket
screws.
SCREW
(ITEM
D)
INNER
WINDOW
SILL
1"(25.4mrr
"
CENTER
LINE
OF WINDOW
_
FIG. 5
SCREW
SUPPORT
INNERSiLL
BRACKET
ABOUT1/4"
__------_
PLEVELING
f
_'_
BOL_uTERfILL
II't
'lJ
/I
I
OUTDOOR
FIG.
6
INDOOR
Failure to securely install support bracket may
result in unit falling from window if window sash is
raised after unit is installed. This could result in
personal injury.
-6-