Kenwood KVT-696 Instruction Manual - Page 94

Parental level - rate

Get Kenwood KVT-696 PDF manuals and user guides
UPC - 019048186126
View all Kenwood KVT-696 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Protect : Protective circuit has been activated because a speaker cord has shorted or it has come in contact with the car chassis. • Wire or insulate the speaker cord as appropriate and then push the Reset button (page 4). Hot Error: When the internal temperature of this unit rises to 60°C or more, the protection circuit is activated and you may not be able to operate the unit. At such times this message will appear. • Use the unit again after reducing the temperature inside the vehicle. Hold Error: Activation of the protective circuit when the temperature inside the disc changer is higher than 60 degrees Celsius stops the disc changer from operating. At such times this message will appear. • Use when the temperature at the site where the disc changer has been fitted has dropped. Mecha Error: The disc player is malfunctioning. • Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues blinking or the disc cannot be ejected. Disc Error: An unplayable disc is inserted. Read Error: Disc is quite dirty. • Clean the disc. referring tot he section on (page 4). Disc is upside down. • Load the disc with the labeled side up. Region code Error: The disc you wanted to play has a region code that cannot be played with this unit. Parental level Error: The disc you wanted to play has a higher level than the parental level you set. Error 07-67: The unit is not operating correctly due to some reason or other. • Push the unit's Reset button. If the "Error 07-67" message does not disappear, see your nearest Kenwood dealer. No Device {USB device)/Disconnected (iPod): The USB device/iPod is selected as a source although no USB device/iPod is connected. • Change the source to any source other than USB/iPod. Connect an USB device/iPod, and change the source to USB/iPod again. No Music: The connected USB device contains no playable audio file. Media was played that doesn't have data recorded that the unit can play. USB Device Error!!: The connected USB device is rated a current capacity higher than the allowable limit. • Check the USB device. Some trouble may have occurred to the connected USB device. • Change the source to any source other than USB. Remove the USB device. Authorization Error: Connection to the iPod has failed. • Remove the iPod and then reconnect it. The unit does not support the iPod. • See (page 5). Update your iPod: The iPod's software is an older version which the unit can not support. • Confirm that the software for the iPod is the latest version. See (page 5). No Navigation: This unit does not support the connected navigation unit. • The latest information on the connectable navigation unit can be obtained from http:// www.kenwood.com/cs/ce. No navigation unit is connected. • Connect a supported navigation unit. 94 KVT-696/KVT-636DVD/KVT-516/KVT-546DVD

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Protect :
Protective circuit
has
been activated because a speaker
cord
has
shorted or it
has
come
in
contact with the
car
chassis.
•
Wire
or
insulate
the
speaker cord
as
appropriate
and
then
push
the
Reset
button
(page
4).
Hot Error:
When the internal temperature
of
this unit
rises
to
60°C
or more, the protection circuit
is
activated and you
may
not
be
able to operate the unit.
At
such
times this
message
will appear.
•
Use
the
unit
again after reducing the
temperature inside
the
vehicle.
Hold Error:
Activation
of
the protective circuit when the
temperature inside the disc changer
is
higher than
60
degrees
Celsius
stops the disc changer from operating.
At
such
times this message will appear.
•
Use
when
the
temperature
at
the
site where
the
disc changer
has
been fitted
has
dropped.
Mecha Error:
The
disc player
is
malfunctioning.
•
Eject
the
disc and
try
inserting it again. Contact
the Kenwood dealer
if
this indicator continues
blinking or
the
disc
cannot
be ejected.
Disc
Error:
An unplayable disc
is
inserted.
Read Error:
Disc
is
quite dirty.
•
Clean
the
disc. referring
tot
he section
on
<Handling discs> (page
4).
Disc
is
upside down.
•
Load
the
disc
with
the
labeled side up.
Region code Error:
The
disc you wanted to play
has
a region code that
cannot
be
played with this unit.
Parental level
Error:
The
disc you wanted to play
has
a higher
level
than the
parental
level
you
set.
94
KVT-696/KVT-636DVD/KVT-516/KVT-546DVD
Error
07-67:
The
unit
is
not operating correctly due
to
some
reason
or other.
•
Push
the
unit's Reset
button.
If
the
"Error
07-67"
message does
not
disappear,
see
your nearest
Kenwood dealer.
No Device
{USB
device)/Disconnected (iPod):
The
USB
device/iPod
is
selected
as
a source although
no
USB
device/iPod
is
connected.
•
Change
the
source
to
any source
other
than
USB/iPod. Connect an
USB
device/iPod, and
change
the
source
to
USB/iPod again.
No Music:
The
connected
USB
device contains no playable audio
file.
Media
was
played that doesn't
have
data recorded that
the unit
can
play.
USB
Device Error!!:
The
connected
USB
device
is
rated a current capacity
higher than the allowable limit.
•
Check
the
USB
device.
Some trouble may have occurred to the connected
USB
device.
•
Change
the
source
to
any source
other
than
USB.
Remove
the
USB
device.
Authorization Error:
Connection to the
iPod
has
failed.
•
Remove
the
iPod and
then
reconnect it.
The
unit does not support the
iPod.
•
See
<iPod/iPhone models
that
can be
connected
to
this
unit>
(page
5).
Update your iPod:
The
iPod's
software
is
an
older version which the unit
can
not support.
•
Confirm
that
the
software for the iPod
is
the
latest version.
See
<iPod/iPhone models
that
can
be
connected
to
this
unit>
(page
5).
No Navigation:
This
unit does not support the connected navigation
unit.
•
The latest
information
on the connectable
navigation
unit
can be
obtained
from
http://
www.kenwood.com/cs/ce.
No navigation
unit
is
connected.
•
Connect a
supported
navigation unit.