Kenwood NX-3320 User Manual - Page 29

Send the GPS Data <GPS_TX&gt, Scan Delete/ Add <D/A&gt

Get Kenwood NX-3320 PDF manuals and user guides View all Kenwood NX-3320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

o RX Audio Equalizer (Low) Allows you to set the audio response for low frequencies. o RX Auto Gain Control Allows you to set the transceiver to automatically adjust the volume of the receiving sound to a specific level for easy listening. o Save Log Data Allows you to save the operation and communication logs of this transceiver. o Scan Refer to "SCAN" {p. 33} . o Scan Delete/ Add Allows you to include or omit each channel in the scan sequence. o Scan Normal Allows you to forcibly perform a non-priority scan even when priority scan has been set. o Scan Program Allows you to reprogram the Scan List and Priority channels using your transceiver. Refer to "SCAN PROGRAMMING" {p. 34} . o Scrambler/ Encryption Allows you to prevent a third party from listening in on your call. Refer to "SCRAMBLER (ANALOG/ LTR)/ ENCRYPTION (NXDN/ DMR)" {p. 40} . o Scrambler/ Encryption Code Allows you to change the scrambler code used in the transmission. Refer to "SCRAMBLER (ANALOG/ LTR)/ ENCRYPTION (NXDN/ DMR)" {p. 40} . o Send the GPS Data For Portable transceivers, this allows you to send your positioning data to the base station when a GPS unit has been installed. For Mobile transceivers, this allows you to send your positioning data to the base station. However, the following must be noted. ● When using the NX-3720G, NX-3720HG, NX-3820G, NX-3820HG, you must connect a KRA-40 GPS antenna. ● When using the NX-3720, NX-3720H, NX-3820, NX-3820H, you must connect an external GPS unit. ● When the power is turned ON and/or the reception condition of the GPS satellite is poor, positioning may take longer to complete. ● When using the built-in GPS Receiver, "GPS Ant Fail" appears on the display if the GPS antenna is not connected or the connection is abnormal (e.g. short circuit). o Short Message Allows you to send short messages such as an address, telephone number, etc. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
o
RX Audio Equalizer (Low)
Allows you to set the audio response for low frequencies.
o
RX Auto Gain Control
Allows you to set the transceiver to automatically adjust the volume of the receiving
sound to a specific level for easy listening.
o
Save Log Data <Log>
Allows you to save the operation and communication logs of this transceiver.
o
Scan <Scan>
Refer to “SCAN” {p. 33} .
o
Scan Delete/ Add <D/A>
Allows you to include or omit each channel in the scan sequence.
o
Scan Normal <ScnNrm>
Allows you to forcibly perform a non-priority scan even when priority scan has been
set.
o
Scan Program <ScnPrg>
Allows you to reprogram the Scan List and Priority channels using your transceiver.
Refer to “SCAN PROGRAMMING” {p. 34} .
o
Scrambler/ Encryption <Scr/ Encryp>
Allows you to prevent a third party from listening in on your call. Refer to
“SCRAMBLER (ANALOG/ LTR)/ ENCRYPTION (NXDN/ DMR)” {p. 40} .
o
Scrambler/ Encryption Code
Allows you to change the scrambler code used in the transmission. Refer to
“SCRAMBLER (ANALOG/ LTR)/ ENCRYPTION (NXDN/ DMR)” {p. 40} .
o
Send the GPS Data <GPS_TX>
For Portable transceivers, this allows you to send your positioning data to the base
station when a GPS unit has been installed.
For Mobile transceivers, this allows you to send your positioning data to the base
station. However, the following must be noted.
●
When using the NX-3720G, NX-3720HG, NX-3820G, NX-3820HG, you must connect a
KRA-40 GPS antenna.
●
When using the NX-3720, NX-3720H, NX-3820, NX-3820H, you must connect an external
GPS unit.
●
When the power is turned ON and/or the reception condition of the GPS satellite is poor,
positioning may take longer to complete.
●
When using the built-in GPS Receiver, “GPS Ant Fail” appears on the display if the GPS
antenna is not connected or the connection is abnormal (e.g. short circuit).
o
Short Message <SDM>
Allows you to send short messages such as an address, telephone number, etc.
29