LG RU-44SZ63D Owners Manual - Page 48

Press the POWERbutton - model

Get LG RU-44SZ63D - LG - 44inch Rear Projection TV PDF manuals and user guides
UPC - 719192168046
View all LG RU-44SZ63D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

The remote contro[ for your HD receiver is a mu[ti-brand or universa[ remote contro[ that can be programmed to operate most remote-contro[[able devices of other manufacturers. Note: The remote contro[ may not be ab[e to contro[ a[[ models of other brands. Test your remote control To find out whether your remote control can operate the device without programming, turn on the device such as a the VCR and press the corresponding mode button (VCR) on the remote control while pointing at the device. Test the POWER and CH +/- buttons to see if the device responds properly. If not, the remote requires programming to operate the device. Turn on the device to be programmed. Then press the corresponding mode button on the remote control L Press the POWERbutton and the MUTE butF ton simu[taneous[y. Now the remote control is ready to program the code for the corresponding device. There are two ways to find the right code for the device. A. If you press the CH +/- buttons repeatedly, the codes wi[[ change one at a time. Press the POWER button after each code change. If the right code is found, the device wi[[ turn off. B. Enter a code number using the number buttons on the remote. The right code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device wi[[ turn off. Press the EXIT button to store the program. Test the remote contro[ functions to see if the device responds properly. If not, repeat from step 2. PAGE 48 TV VCR CABLE DVD SAT © oooo MODE LIGHT POWER TVA/IDEO FRONT DVI (2)(2)(2) COMP1 COMP2 RGB C) C) PIP PIPCH- PIPCH+ SWAP 0000 0000 PLAY PAUSE STOP RECORD ®®®® REW FF

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
The
remote
contro[
for
your
HD receiver
is
a
mu[ti-brand
or universa[ remote contro[
that
can
be programmed
to
operate most remote-contro[-
[able devices of other manufacturers.
Note: The remote contro[
may not be ab[e to con-
tro[
a[[ models of other brands.
Test your remote control
To find out whether your remote control
can
operate
the
device
without
programming,
turn
on the device
such as a the VCR and
press the corresponding
mode button
(VCR)
on the remote control
while
pointing
at the
device. Test the POWER and CH +/-
buttons
to
see if
the
device
responds
properly.
If
not,
the
remote
requires
programming
to
operate the device.
Turn on the device to
be programmed. Then
press the corresponding
mode button
on the
remote control
Press the POWERbutton
and the MUTE but-
ton simu[taneous[y.
Now the remote control
is ready to program
the code for the corre-
sponding
device.
L
F
There are two ways to find the right
code for
the device.
A. If
you press the
CH
+/-
buttons
repeat-
edly, the codes wi[[
change one at a time.
Press the
POWER button
after
each
code
change.
If
the
right
code is
found,
the
device wi[[ turn
off.
B. Enter a code number
using the
number
buttons
on the remote. The right
code num-
bers for
the corresponding
component
can
be found on the following
pages.
Again, if the code is correct, the device wi[[
turn
off.
Press the EXIT button
to store the program.
Test the remote
contro[
functions
to
see if
the device responds properly.
If not,
repeat
from step 2.
TV
VCR CABLE DVD
SAT
©
o
o
o
o
MODE
LIGHT
POWER
TVA/IDEO
FRONT
DVI
(2)(2)(2)
COMP1
COMP2
RGB
C)
C)
®®
®®
@®@
PIP
PIPCH- PIPCH+
SWAP
0000
0000
PLAY
PAUSE
STOP
RECORD
®®®®
REW
FF
PAGE
48