Lantronix EDS4100 EDS - User Guide - Page 62

Tunnel Packing Mode, Submit., Tunnel, Packing Mode, Settings, Description

Get Lantronix EDS4100 PDF manuals and user guides View all Lantronix EDS4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

9: Line and Tunnel Settings Tunnel - Packing Mode Settings Mode Threshold (Appears for both Timeout and Send Character Modes) Timeout (Appears for Timeout Mode) Send Character (Appears for Send Character Mode) Trailing Character (Appears for Send Character Mode) Table 9-12 Tunnel Packing Mode Description  Select Disable to disable Packing Mode completely.  Select Timeout to send data after the specified time has elapsed.  Select Send Character to send the queued data when the send character is received. Send the queued data when the number of queued bytes reaches the threshold. When the buffer fills to this specified amount of data in bytes (and the timeout has not elapsed), the device packs the data and sends it out; applies only if the Packing Mode is not Disabled. Enter a time, in milliseconds, for the device to send the queued data after the first character was received. Specifies the time duration in milliseconds; applies only if the Packing Mode is Timeout. Enter the send character (single printable or control). Upon receiving this character, the device sends out the queued data. The data is packed until the specified send character is encountered. Similar to a start or stop character, the device packs the data until it sees the send character. The device then sends the packed data and the send character in the packet. Applies only if the Packing Mode is Send Character. Enter the trailing character (single printable or control). This character is sent immediately following the send character. This is an optional setting. If a trailing character is defined, this character is appended to data put on the network immediately following the send character. 5. Click Submit. 6. Repeat above steps as desired, according to additional tunnel(s) available on your product. EDS User Guide 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
9: Line and Tunnel Settings
EDS User Guide
62
Table 9-12
Tunnel Packing Mode
5.
Click
Submit.
6.
Repeat above steps as desired, according to additional tunnel(s) available on your product.
Tunnel -
Packing Mode
Settings
Description
Mode
Select
Disable
to disable Packing Mode completely.
Select
Timeout
to send data after the specified time has
elapsed.
Select
Send Character
to send the queued data when the send
character is received.
Threshold
(Appears for both Timeout
and Send Character
Modes)
Send the queued data when the number of queued bytes reaches
the threshold.
When the buffer fills to this specified amount of data
in bytes (and the timeout has not elapsed), the device packs the
data and sends it out; applies only if the Packing Mode is not
Disabled.
Timeout
(Appears for Timeout
Mode)
Enter a time, in milliseconds, for the device to send the queued
data after the first character was received.
Specifies the time
duration in milliseconds; applies only if the Packing Mode is
Timeout.
Send Character
(Appears for Send
Character Mode)
Enter the send character (single printable or control). Upon
receiving this character, the device sends out the queued data.
The data is packed until the specified send character is
encountered. Similar to a start or stop character, the device packs
the data until it sees the send character. The device then sends the
packed data and the send character in the packet.
Applies only if
the Packing Mode is Send Character.
Trailing Character
(Appears for Send
Character Mode)
Enter the trailing character (single printable or control). This
character is sent immediately following the send character.
This is
an optional setting. If a trailing character is defined, this character is
appended to data put on the network immediately following the
send character.