Lantronix EDS8PS EDS - Command Reference - Page 189

line 4 line:4 level commands, Uses two stop bits after data on the line.

Get Lantronix EDS8PS PDF manuals and user guides View all Lantronix EDS8PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 189 highlights

no gap timer no name parity even parity none parity odd protocol lpd protocol lpd or tunnel protocol modbus ascii protocol modbus rtu protocol none protocol tunnel reassert show show command mode show history show line show statistics state disable state enable stop bits 1 stop bits 2 terminal terminal network threshold tunnel write xoff char xon char line 4 (line:4) level commands auto show statistics baud rate EDS Command Reference 5: Commands and Levels Removes the gap timer, so forwarding depends on the line speed. Removes the name of this line. Uses a parity bit on the line for even parity. Does not use a parity bit on the line. Uses a parity bit on the line for odd parity. Applies Line Printer Daemon (LPD) protocol on the line. Applies LPD or tunnel protocol on the line. Applies Modbus ASCII protocol on the line. Applies Modbus RTU protocol on the line. Uses no protocol on the line. Applies tunnel protocol on the line. Asserts line status with current configured values. Displays the current status. Shows the command mode settings for the current line. Displays the last 20 commands entered during the current CLI session. Displays the current configuration. Shows the line statistics. Disables the line so data cannot be sent/received. Enables the line so data can be sent/received. Uses one stop bit after data on the line. Uses two stop bits after data on the line. Enters the configure-terminal level. = number of the terminal line (serial port) to be configured. Enters the configure-terminal level for the network. Sets the threshold in bytes. After this many bytes are received, they are forwarded without delay. Enters the tunnel level. = number of the tunnel line (serial port) to be configured. Stores the current configuration in permanent memory. Sets the xoff character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. Sets the xon character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. Continuously displays line statistics. Sets the line speed. = the speed. 189

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
5:
Commands and Levels
EDS Command Reference
189
no gap timer
Removes the gap timer, so forwarding depends on the
line speed.
no name
Removes the name of this line.
parity even
Uses a parity bit on the line for even parity.
parity none
Does not use a parity bit on the line.
parity odd
Uses a parity bit on the line for odd parity.
protocol lpd
Applies Line Printer Daemon (LPD) protocol on the line.
protocol lpd or tunnel
Applies LPD or tunnel protocol on the line.
protocol modbus ascii
Applies Modbus ASCII protocol on the line.
protocol modbus rtu
Applies Modbus RTU protocol on the line.
protocol none
Uses no protocol on the line.
protocol tunnel
Applies tunnel protocol on the line.
reassert
Asserts line status with current configured values.
show
Displays the current status.
show command mode
Shows the command mode settings for the current line.
show history
Displays the last 20 commands entered during the current
CLI session.
show line
Displays the current configuration.
show statistics
Shows the line statistics.
state disable
Disables the line so data cannot be sent/received.
state enable
Enables the line so data can be sent/received.
stop bits 1
Uses one stop bit after data on the line.
stop bits 2
Uses two stop bits after data on the line.
terminal
<line>
Enters the configure-terminal level.
<line> = number of the terminal line (serial port) to be
configured.
terminal network
Enters the configure-terminal level for the network.
threshold
<bytes>
Sets the threshold in bytes. After this many bytes are
received, they are
forwarded without delay.
tunnel
<line>
Enters the tunnel level.
<line> = number of the tunnel line (serial port) to be
configured.
write
Stores the current configuration in permanent memory.
xoff char
<control>
Sets the xoff character for use with software flow control
on this line.
The character may be input as text, control, decimal, or
hex.
A control character has the form <control>C.
A decimal value character has the form \99.
A hex value character has the form 0xFF.
xon char
<control>
Sets the xon character for use with software flow control
on this line.
The character may be input as text, control, decimal, or
hex.
A control character has the form <control>C.
A decimal value character has the form \99.
A hex value character has the form 0xFF.
line 4 (line:4) level commands
auto show statistics
Continuously displays line statistics.
baud rate
<bits per second>
Sets the line speed.
<bits per second> = the speed.