Lenovo 7515-J9U User Guide - Page 32

Connecting a SATA drive, Locate an available SATA connector on the system board. See Locating parts

Get Lenovo 7515-J9U - ThinkCentre A58 Desktop PC PDF manuals and user guides
UPC - 884942137211
View all Lenovo 7515-J9U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

4. Install the retainer that comes with your drive on the side of the drive. Figure 14. Installing the drive retainer 5. Install the drive into the bay. Figure 15. Installing the drive 6. To reinstall the front bezel, align the plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position on the left side. 7. Continue at "Connecting a SATA drive." Connecting a SATA drive: A SATA optical drive or a SATA hard disk drive can be connected to any available SATA connector. To connect a SATA drive: 1. Locate the signal cable that comes with the new drive. 2. Locate an available SATA connector on the system board. See "Locating parts on the system board" on page 11. 3. Connect one end of the signal cable to the drive and the other end to the available SATA connector on the system board. 24 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
4.
Install the retainer that comes with your drive on the side of the drive.
5.
Install the drive into the bay.
6.
To reinstall the front bezel, align the plastic tabs on the right side of the front
bezel with the corresponding holes in the chassis, then pivot the front bezel
inward until it snaps into position on the left side.
7.
Continue at “Connecting a SATA drive.”
Connecting a SATA drive:
A SATA optical drive or a SATA hard disk drive can
be connected to any available SATA connector.
To connect a SATAdrive:
1.
Locate the signal cable that comes with the new drive.
2.
Locate an available SATA connector on the system board. See “Locating parts
on the system board” on page 11.
3.
Connect one end of the signal cable to the drive and the other end to the
available SATA connector on the system board.
Figure 14. Installing the drive retainer
Figure 15. Installing the drive
24
User Guide