Lenovo ThinkCentre M91p (English) User Guide - Page 48

Connect the signal cable and the power cable to the rear of the new hard disk drive.

Get Lenovo ThinkCentre M91p PDF manuals and user guides View all Lenovo ThinkCentre M91p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

4. Press inward on the side tabs of the hard disk drive bracket. Place your finger on the tab located on the front of the hard disk drive bracket and then pivot the hard disk drive upward to remove it from the hard disk drive bay. Figure 15. Removing the hard disk drive 5. Disconnect the signal cable and the power cable from the rear of the hard disk drive. 6. Flex the sides of the hard disk drive bracket properly to remove the hard disk drive out of the bracket. 7. To install the new hard disk drive into the bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 16. Installing the hard disk drive into the bracket 8. Connect the signal cable and the power cable to the rear of the new hard disk drive. 9. Slide the new hard disk drive into the hard disk drive bay and pivot it down until it snaps into position. 10. Reconnect the power cable to the optical drive. What to do next: • To work with another piece of hardware, go to the appropriate section. 34 ThinkCentre User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
4. Press inward on the side tabs of the hard disk drive bracket. Place your finger on the tab located
on the front of the hard disk drive bracket and then pivot the hard disk drive upward to remove it
from the hard disk drive bay.
Figure 15. Removing the hard disk drive
5. Disconnect the signal cable and the power cable from the rear of the hard disk drive.
6. Flex the sides of the hard disk drive bracket properly to remove the hard disk drive out of the bracket.
7. To install the new hard disk drive into the bracket, flex the bracket and align pin
1
, pin
2
, pin
3
, and
pin
4
on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit
board
5
on the bottom of the hard disk drive.
Figure 16. Installing the hard disk drive into the bracket
8. Connect the signal cable and the power cable to the rear of the new hard disk drive.
9. Slide the new hard disk drive into the hard disk drive bay and pivot it down until it snaps into position.
10. Reconnect the power cable to the optical drive.
What to do next:
•
To work with another piece of hardware, go to the appropriate section.
34
ThinkCentre User Guide