Home » LevelOne Manuals » Security Cameras » LevelOne FCS-5061 » Manual Viewer

LevelOne FCS-5061 Manual - Page 16

Example of Changing IP Camera's Network Property, Step 1

Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

The default login ID and password for the Administrator are: Login ID root Password NOTE: ID and password are case sensitive. NOTE: It is strongly advised that administrator's password be altered for the security concerns. Additionally, users can change the IP Camera's network property, either DHCP or Static IP directly in the device finding list. Refer to the following section for changing the IP Camera's network property. Example of Changing IP Camera's Network Property Users can directly change an IP Camera's network property, ex. from static IP to DHCP, in the finding device list. The way to change the IP Camera's network property is specified below: Step 1: In the finding device list, click on the IP Camera that you would like to change its network property. On the selected item, right click and select "Network Setup." Meanwhile, record the IP Camera's MAC address, for future identification. 16

Section	Page
1. Overview	5
1.1 Features	5
1.2 Package Contents	6
1.3 Dimensions	7
1.4 Connectors	8
2. Camera Cabling	10
2.1 Connect Power	10
2.2 Connect Ethernet Cable	11
2.3 Connect Alarm I/O	11
3. Installation	12
3.1 Ceiling/Wall Mounting	12
4. System Requirements	13
5. Accessing Camera	14
5.1 Using Recording Software	18
5.2 Installing DC Viewer Software Online	19
6. Configuration & Operation	21
6.1 Browser-based Viewer Introduction	21
6.2 Home Page	23
6.3 System Related Settings	25
6.3.1 Host Name and System Time Setting	26
6.3.2 Security	27
6.3.2.1 User	28
6.3.2.2 HTTPS	30
6.3.2.3 IP Filter	32
6.3.2.4 IEEE 802.1X	33
6.3.3 Network	35
6.3.3.1 Basic	36
6.3.3.2 QoS	39
6.3.3.3 SNMP	41
6.3.3.4 UPnP	43
6.3.4 DDNS	45
6.3.5 Mail	46
6.3.6 FTP	47
6.3.7 HTTP	48
5.3.8 Application	49
6.3.9 Motion Detection	54
6.3.10 Network Failure Detection	60
6.3.11 Tampering	62
6.3.12 Storage Management (Local Recording)	65
6.3.13 Recording (Local Recording)	67
6.3.14 File Location (Snapshots and Web Recording)	68
6.3.15 View Information	69
6.3.15.1 Log File	70
6.3.15.2 User Information	71
6.3.15.3 Parameters	72
6.3.16 Factory Default	73
6.3.17 Software Version	74
6.3.18 Software Upgrade	75
6.3.19 Maintenance	77
6.4 Streaming	79
6.4.1 Video Resolution and Rotate Type	80
6.4.2 Video Compression	82
6.4.3 Video ROI	83
6.4.4 Video OCX Protocol	85
6.4.5 Video Frame Rate	86
6.4.6 Video Mask	87
6.4.7 Audio (Audio Mode and Bit Rate Settings)	88
6.5 Camera Settings	90
6.5.1 Exposure Setting	91
6.5.2 White Balance Setting	92
/6.5.3 Brightness Setting	93
6.5.4 Backlight	94
6.5.5 Digital Zoom	94
6.5.6 IR Function	94
6.5.7 WDR Function	95
6.5.8 Noise Reduction	95
6.5.9 TV System Setup	96
6.6 Logout	96
Appendix A: Technical Specifications	97
Appendix B: Internet Security Settings	99
Appendix C: DC Viewer Download Procedure	102

Match case Limit results 1 per page

The default login ID and password for the Administrator are:

Password

root

NOTE:

ID and password are case sensitive.

NOTE:

It is strongly advised that administrator’s password be altered

for the security concerns.

Additionally, users can change the IP Camera’s network property, either DHCP or Static

IP directly in the device finding list. Refer to the following section for changing the IP

Camera’s network property.

Example of Changing IP Camera’s Network Property

Users can directly change an IP Camera’s network property, ex. from static IP to DHCP,

in the finding device list. The way to change the IP Camera’s network property is specified

below:

Step 1:

In the finding device list, click on the IP Camera that you would like to change its network

property. On the selected item, right click and select “Network Setup.” Meanwhile, record

the IP Camera’s MAC address, for future identification.