LevelOne FCS-5061 Manual - Page 57

53

Record stream to SD Card

Select this item and the Motion Detection recording will be stored in Micro

SD/ SDHC card when motion is detected.

Pre-trigger buffer recording function allows users to check what happened to

cause the trigger. The pre-trigger buffer time range is from 1 to 3 seconds.

Select <Upload for __ sec> to set the recording duration after motion event

occurs. The setting range is from 1 to 99999 seconds.

Select <Upload during the trigger active> to record the triggered video

until the trigger is off.

NOTE:

Please make sure the local recording (with Micro SD/

SDHC card) is activated so that this function can be implemented.

See section

“Recording”

for further details.

Send Alarm Message by FTP/E-Mail

The Administrator can select whether to send an alarm message by

FTP and/or E-Mail when motion is detected.

Upload Image by FTP

Select this item and the Administrator can assign a FTP site and configure

various parameters. When motion is detected, event images will be uploaded

to the appointed FTP site.

<Pre-trigger buffer> function allows users to check what happened to cause

the trigger. The <Pre-trigger buffer> frame rate could be pre-determined.

On the other hand, <Post-trigger buffer> is for users to upload certain amount

of images after motion event occurs.

Check the box <Continue image upload> to upload the triggered images

during certain time or keep uploading until the trigger is off. Select <Upload

for __sec> and enter the duration in the blank. The images of the duration will

be uploaded to FTP when the motion event occurs. The setting range is from

1 to 9999 seconds. Select <Upload during the trigger active> to make the

images keep being uploaded to FTP during the trigger active until the event

stops. Set the Image frequency as the upload frame rate. The setting range is

from 1 frame to 15 frames.

Section	Page
1. Overview	5
1.1 Features	5
1.2 Package Contents	6
1.3 Dimensions	7
1.4 Connectors	8
2. Camera Cabling	10
2.1 Connect Power	10
2.2 Connect Ethernet Cable	11
2.3 Connect Alarm I/O	11
3. Installation	12
3.1 Ceiling/Wall Mounting	12
4. System Requirements	13
5. Accessing Camera	14
5.1 Using Recording Software	18
5.2 Installing DC Viewer Software Online	19
6. Configuration & Operation	21
6.1 Browser-based Viewer Introduction	21
6.2 Home Page	23
6.3 System Related Settings	25
6.3.1 Host Name and System Time Setting	26
6.3.2 Security	27
6.3.2.1 User	28
6.3.2.2 HTTPS	30
6.3.2.3 IP Filter	32
6.3.2.4 IEEE 802.1X	33
6.3.3 Network	35
6.3.3.1 Basic	36
6.3.3.2 QoS	39
6.3.3.3 SNMP	41
6.3.3.4 UPnP	43
6.3.4 DDNS	45
6.3.5 Mail	46
6.3.6 FTP	47
6.3.7 HTTP	48
5.3.8 Application	49
6.3.9 Motion Detection	54
6.3.10 Network Failure Detection	60
6.3.11 Tampering	62
6.3.12 Storage Management (Local Recording)	65
6.3.13 Recording (Local Recording)	67
6.3.14 File Location (Snapshots and Web Recording)	68
6.3.15 View Information	69
6.3.15.1 Log File	70
6.3.15.2 User Information	71
6.3.15.3 Parameters	72
6.3.16 Factory Default	73
6.3.17 Software Version	74
6.3.18 Software Upgrade	75
6.3.19 Maintenance	77
6.4 Streaming	79
6.4.1 Video Resolution and Rotate Type	80
6.4.2 Video Compression	82
6.4.3 Video ROI	83
6.4.4 Video OCX Protocol	85
6.4.5 Video Frame Rate	86
6.4.6 Video Mask	87
6.4.7 Audio (Audio Mode and Bit Rate Settings)	88
6.5 Camera Settings	90
6.5.1 Exposure Setting	91
6.5.2 White Balance Setting	92
/6.5.3 Brightness Setting	93
6.5.4 Backlight	94
6.5.5 Digital Zoom	94
6.5.6 IR Function	94
6.5.7 WDR Function	95
6.5.8 Noise Reduction	95
6.5.9 TV System Setup	96
6.6 Logout	96
Appendix A: Technical Specifications	97
Appendix B: Internet Security Settings	99
Appendix C: DC Viewer Download Procedure	102

LevelOne FCS-5061 Manual - Page 57

Record stream to SD Card, Send Alarm Message by FTP/E-Mail, Upload Image by FTP, On the other hand

Page 57 highlights