LevelOne FCS-5061 Manual - Page 56

Motion Detection Setting, Enable Alarm Output

Get LevelOne FCS-5061 PDF manuals and user guides View all LevelOne FCS-5061 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Motion Detection You will be able to turn on/off Motion Detection in System section. Default setting is Off. Motion Detection Setting Users could adjust various parameters of Motion Detection in this section. Sampling pixel interval [1-10]: The default value is 1. If the value is set as 3, it means within the detection region, system will take one sampling pixel for every 3 pixels by each row and each column (refer to the figure below). Detection level [1-100]: The default level is 10. The item is to set detection level for each sampling pixel; the smaller the value, the more sensitive it is. Sensitivity level [1-100]: The default level is 80, which means if 20% or more sampling pixels are detected differently, system will detect motion. The bigger the value, the more sensitive it is. Meanwhile, when the value is bigger, the red horizontal line in the motion indication window will be lower accordingly. Time interval (sec) [0-7200]: The default interval is 10. The value is the interval between each detected motion. Triggered Action (Multi-option) The Administrator can specify alarm actions that will take when motion is detected. All options are listed as follows: Enable Alarm Output Check the item and select the predefined type of alarm output to enable alarm relay output when motion is detected. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
52
Motion Detection
You will be able to turn on/off Motion Detection in System section. Default
setting is Off.
Motion Detection Setting
Users could adjust various parameters of Motion Detection in this section.
Sampling pixel interval [1-10]:
The default value is 1. If the value is set as 3, it means within the
detection region, system will take one sampling pixel for every 3 pixels
by each row and each column (refer to the figure below).
Detection level [1-100]:
The default level is 10. The item is to set detection level for each
sampling pixel; the smaller the value, the more sensitive it is.
Sensitivity level [1-100]:
The default level is 80, which means if 20% or more sampling pixels are
detected differently, system will detect motion. The bigger the value, the more
sensitive it is. Meanwhile, when the value is bigger, the red horizontal line in
the motion indication window will be lower accordingly.
Time interval (sec) [0-7200]:
The default interval is 10. The value is the interval between each detected
motion.
Triggered Action
(Multi-option)
The Administrator can specify alarm actions that will take when motion is
detected. All options are listed as follows:
Enable Alarm Output
Check the item and select the predefined type of alarm output to enable alarm
relay output when motion is detected.