LevelOne FCS-5061 Manual - Page 51

51

Upload Image by E-Mail

Select this item, and the Administrator can assign an e-mail address and

configure various parameters as shown in the figure below. When the

alarm is triggered, event images will be sent to the appointed e-mail

address.

<Pre-trigger buffer> function allows users to check what happened to

cause the trigger. The <Pre-trigger buffer> frame rate could be pre-

determined.

On the other hand, <Post-trigger buffer> is for users to upload certain

amount of images after alarm input is triggered.

Check the box <Continue image upload> to upload the triggered images

during certain time or keep uploading until the trigger is off. Select

<Upload for __sec> and enter the duration in the blank. The images of

the duration will be uploading by E-mail when the alarm input is triggered.

The setting range is from 1 to 9999 seconds. Select <Upload during the

trigger active> to make the images keep being uploaded to E-mail during

the trigger active until the alarm is released. Set the Image frequency as

the upload frame rate. The setting range is from 1 frame to 15 frames.

NOTE:

Make sure SMTP or FTP configuration has been completed. See

section

Mail

and

FTP

for further details.

Send HTTP notification

Check this item, select the destination HTTP address, and specify the

parameters for event notifications by <Alarm> triggered. When an alarm

is triggered, the notification can be sent to the specified HTTP server.

For instance, if the custom parameter is set as” action=1&group=2”, and

the HTTP server name is” http://192.168.0.1/admin.php”, the notification

will be sent to HTTP server as” http://192.168.0.1/admin.php?

action=1&group=2” when alarm is triggered.

Record Stream to SD Card

Select the item and the alarm-triggered recording will be saved into your

Micro SD card.

Pre-trigger buffer recording function allows users to check what

Section	Page
1. Overview	5
1.1 Features	5
1.2 Package Contents	6
1.3 Dimensions	7
1.4 Connectors	8
2. Camera Cabling	10
2.1 Connect Power	10
2.2 Connect Ethernet Cable	11
2.3 Connect Alarm I/O	11
3. Installation	12
3.1 Ceiling/Wall Mounting	12
4. System Requirements	13
5. Accessing Camera	14
5.1 Using Recording Software	18
5.2 Installing DC Viewer Software Online	19
6. Configuration & Operation	21
6.1 Browser-based Viewer Introduction	21
6.2 Home Page	23
6.3 System Related Settings	25
6.3.1 Host Name and System Time Setting	26
6.3.2 Security	27
6.3.2.1 User	28
6.3.2.2 HTTPS	30
6.3.2.3 IP Filter	32
6.3.2.4 IEEE 802.1X	33
6.3.3 Network	35
6.3.3.1 Basic	36
6.3.3.2 QoS	39
6.3.3.3 SNMP	41
6.3.3.4 UPnP	43
6.3.4 DDNS	45
6.3.5 Mail	46
6.3.6 FTP	47
6.3.7 HTTP	48
5.3.8 Application	49
6.3.9 Motion Detection	54
6.3.10 Network Failure Detection	60
6.3.11 Tampering	62
6.3.12 Storage Management (Local Recording)	65
6.3.13 Recording (Local Recording)	67
6.3.14 File Location (Snapshots and Web Recording)	68
6.3.15 View Information	69
6.3.15.1 Log File	70
6.3.15.2 User Information	71
6.3.15.3 Parameters	72
6.3.16 Factory Default	73
6.3.17 Software Version	74
6.3.18 Software Upgrade	75
6.3.19 Maintenance	77
6.4 Streaming	79
6.4.1 Video Resolution and Rotate Type	80
6.4.2 Video Compression	82
6.4.3 Video ROI	83
6.4.4 Video OCX Protocol	85
6.4.5 Video Frame Rate	86
6.4.6 Video Mask	87
6.4.7 Audio (Audio Mode and Bit Rate Settings)	88
6.5 Camera Settings	90
6.5.1 Exposure Setting	91
6.5.2 White Balance Setting	92
/6.5.3 Brightness Setting	93
6.5.4 Backlight	94
6.5.5 Digital Zoom	94
6.5.6 IR Function	94
6.5.7 WDR Function	95
6.5.8 Noise Reduction	95
6.5.9 TV System Setup	96
6.6 Logout	96
Appendix A: Technical Specifications	97
Appendix B: Internet Security Settings	99
Appendix C: DC Viewer Download Procedure	102

LevelOne FCS-5061 Manual - Page 51

Upload Image by E-Mail, Send HTTP notification, Record Stream to SD Card, Micro SD card.

Page 51 highlights