LiftMaster Miracle-One MIRACLE ONE Manual

LiftMaster Miracle-One Manual

Get LiftMaster Miracle-One PDF manuals and user guides View all LiftMaster Miracle-One manuals
Add to My Manuals
Save this manual to your list of manuals

LiftMaster Miracle-One manual content summary:

  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 1
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 2
    Users / Home Owners Swing Gate Systems Warnings and Precautions "Open to the Inside" Mounting Specifications "Open to the Outside" Mounting Specifications Step-by-Step Operator Mounting Instructions Removing the Control/Surge Suppressor Boards Mounting the Control Box Wiring 1 Operator to the Surge
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 3
    closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas. D) The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. E) Controls must be far enough from the gate so that the user is prevented from
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 4
    operator utilizing a non-contact sensor such as a photo beam: 1. See instructions on the placement of non-contact sensor for each type of application. 2. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving. 3. One
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 5
    is not moving. Make sure the power for the gate operator is off. 6. KEEP GATES PROPERLY MAINTAINED. Read the manual. Have a qualified service person make repairs to the gate or gate hardware. 7. The entrance is for vehicles only. Pedestrians must use separate entrance. 8. SAVE THESE INSTRUCTIONS. 4
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 6
    gate operator (or system) that controls a gate which slides in a horizontal direction that is intended for use for vehicular entrance or exit to a drive, parking lot, or the like. Residential vehicular gate operator - Class I - A vehicular gate operator (or system) intended for use in a home of one
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 7
    vehicular gate into service. • Demonstrate the basic functions and safety features of the gate system to owners/end users/general contractors, including how to turn off power and how to operate the manual disconnect feature. • Leave safety instructions, product literature, installation manual and
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 8
    and repair the gate system (End users should never attempt to repair the gate) • Retain and utilize the installation and maintenance manual and safety instructions. • Routinely check all gate operator functions and gate movement. • Discontinue use if safety systems operate improperly, the gate is
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 9
    in sight and away from people and objects until it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE. 4. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person periodically inspect and make repairs to gate hardware. 5. SAVE THESE INSTRUCTIONS. 8
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 10
    Masonry Column Setup Steel Top View Plate Post Setup Gate Hinge Typical Steel 8.5" 25.75" Post Setup Out Gate in Closed Position 7.75" 6" In Miracle 1 in Closed Position 90° / 105° Gate in Open Position Miracle 1 in Open Position Indexing on central hole in the back steel bracket
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 11
    Steel Post Setup 6" Indexing on central hole in the back steel bracket. Indexing on mounting hole in the front steel bracket. 6" 90° / 105° Gate in Open Position Miracle 1 in Open Position 8.5" This Plate Not Supplied 7.75" Out Gate in Closed Position In Miracle 1 in Closed Position 25.75" 10
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 12
    PROCEDURE FOR INSTALLATION Mounting Instructions Step 1: Remove the 4 screws and lift the operator cover off. Step 2: Release the mechanical lock by turning the key to the horizontal position. Step 3: Position the Miracle 1 horizontally level on the closed gate, where desired. For strength
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 13
    FOR INSTALLATION Mounting Instructions Step 4 (con't): The gate must be in the closed position. Make sure the operator is kept level while tack welding the front and back steel brackets and reinforcement steel plates in position. After all tack welding is finished, remove the operator! Refer to
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 14
    has been locked. Completing this successfully finishes the basic mounting of the operator to the gate. The next steps are to make all electrical connections to the operator and control board. Push or Pull Click! Step 10: The following pages show the correct electrical procedures needed for
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 15
    open" and "full closed" positions. Re-tighten armature screws when gate positions are correct. Limit Switch Armature Adjustment Screws Outside Limit Switch Inside Limit Switch Adjustment Screws Inside Limit Switch Outside Limit Switch Limit Switch Armature Step 12: Reinstall the operator cover
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 16
    control board and remove board. 7 Remove three Phillips screws from surge suppressor board and remove board 24 VOLT +24 VAC INPUT MIRACLE SURGE PROTECTION MIRACLE SURGE PROTECTION 1 3 REV OPEN INSIDE NO OFF 60 OPEN OUTSIDE YES ON 3 TIMER CENTRAL POWER CHARGE OK BATTERY LOW CONTROL STRIKE OPEN
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 17
    MIRACLE SURGE PROTECTION ® WIRING 1 OPERATOR TO BOARD LAKE FOREST, CALIFORNIA www.eliteaccess.com Caution: Do Not over-bend the cord from the operator. Important: Install the Conduit (supplied) to secure the wire to the Miracle 1 Control Board Box. If the conduit can not be used, Install a dedicated
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 18
    conduit! Operator 2 (Second) REV A Operator 1 (Master) Caution: Do Not use wire less than 16 gauge up to 200 Ft. Water Tight J-Box Kit Elite # K55 the Master Operator to the Control Board Box. Water Tight Conduit (Not Supplied) Install a dedicated water tight conduit for the Second Operator. DO
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 19
    on the control board to the corresponding position for the proper direction. 8 8 The gate opens inward. The gate opens outward. SENSOR ADJUSTMENT Caution: The sensors must be adjusted while the gate is in the opening or closing cycle. Adjusted by Qualified Service Personnel Minimum Sensitivity
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 20
    Elite gate operator. Although nothing can absorb the tremendous power of a direct lightning strike, proper grounding can protect the gate operator or destroy its integrity, replace it with a single wire length. Connect ground wire to green wire from surge suppressor board Use 12 gauge ground wire
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 21
    SENSOR CENTER LOOP 8 SAFETY LOOP STRIKE INPUT GROUND RADIO +24 VOLT +24 VAC INPUT REV A CONNECTING POWER SUPPLY Connect Elite's plug-in transformer (24 VAC Included) to Surge Suppressor board, terminals #26 and #27. Polarity does not matter. Use low voltage direct burial landscape lighting cable
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 22
    . DO NOT let wire insulation interfere with connection. MIRACLE SURGE PROTECTION Important: Wiring at #21 and #22 will be recognized as an Open Only command, and Will Not close the gate. To automatically Close the gate after an open cycle, the control board timer must be turned ON. 21 22 23 24
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 23
    OPERATOR LOOP SIZE AND PLACEMENT It is VERY important to have enough separation between loops and gates to prevent false detection. Caution: Distance "E" must be a minimum of 4 feet away from open gate! Out In Drawing not to scale Exit Loop Inside H Safety Loop F I G E Distance from open
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 24
    18 Feet 5.5 Feet 21 Feet 6 Feet Center Loop: This loop must have enough space between loop and gate when opened or closed. If driveway is smaller than 18 ft, then D must be 4.5 ft If driveway is . Individual circumstances may alter dimensions. For toll free technical support: 1-888-ELITE-10 23
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 25
    feet 81 feet and up Number of Wire Turns 4 3 2 1 3 The wire is continuously wound in the loop saw cut for the required number of turns. One turn shown. (Refer to table) The wire must be twisted together 6 twists per foot from the end of the saw cut to the loop detector
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 26
    27 Surge Suppressor Elite Part # A 24 19 20 Com N.O. Gnd +24V 23 25 Elite Part # A 24 17 18 Com N.O. Gnd +24V 23 25 For fail safe operation, connect safety loops 27 Surge Suppressor Elite Part # A 24 Com N.O. Gnd +24V 21 22 23 25 Allows gate to automatically open for exiting vehicles. 25
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 27
    I or class II gate operator, like the following: OMRON Retro-Reflective Photocell, Model: E3K-R10K4-NR BURGLAR ALARM INPUT UL SENSOR CENTER LOOP SAFETY LOOP STRIKE INPUT GROUND RADIO +24 VOLT +24 VAC INPUT 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Elite Part # A OMRON Important! This
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 28
    5 Strike Open LED 6 Safety Loop LED 7 Radio Receiver LED 8 Center Loop LED 9 J3 Transformer & Input Commands Connector 10 Central Control LED 11 Batteries Low LED 12 Charger Ok LED 13 Power LED 14 Charging Power Fuse 5678 15 Board Fuse 16 Replace Charging Power Fuse LED 17 Replace Board Fuse LED
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 29
    and Motor Connector 5 Strike Open LED 6 Safety Loop LED 7 Radio Receiver LED 8 Center Loop LED 9 J3 Transformer & Input Commands Connector 10 Central Control LED 11 Charging Power Fuse 12 Board Fuse 13 Replace Charging Power Fuse LED 14 Replace Board Fuse LED 15 Batteries Low LED 5 28 678
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 30
    ) 7 Black Wire from Operator (Power) 8 White Wire from Operator (Power) 9 Red Wire from Operator (Brake) 10 Brown Wire from Operator (Brake) 11 Blue Wire from Operator (Limits) Second Operator Only 12 Green Wire from Operator (Limits) 13 Burglar Alarm Input (Normally Open) 14 Burglar Alarm
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 31
    ) Maglock Connection (Optional) Alarm Connection 123 2 1 or 3 2 Orange Wires Connect for Open Inside 1. Ground - for Open Inside 2. Power OR Connect for Open Outside 2. Power 3. Ground - for Open Outside UL Audio Alarm Connection 1234 1 2 3 4 Burglar Alarm Relay Output 1. Common 2. N. O. UL
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 32
    consecutive events on 24 MIRACLE SURGE PROTECTION BURGLAR ALARM ® The control board provides a relay with a normally open gate closed position. Proximity Switch (Normally Open) If the gate is forced open 21 22 23 Proximity Switch Normally Open Elite Part # A PRS Removable Terminal Connectors
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 33
    wire to open gate Inside 2. Power - Always plugged in (red wire) Control Board Elite Part # Q240 MAU Contact Rating 125 VAC - 0.5 A 30 VDC - 2 A ...Magnetic Lock Wiring Custom Bracket Magnetic Lock Plate Magnetic Lock Elite Part # A MG 1300 Gate Fence N.C. Common Power for Maglock Note
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 34
    Ground- Plug in white wire to open gate Outside Control Board Elite Part # Q240 MAU Contact Rating 125 VAC - 0.5 A 30 VDC - 2 A ...Magnetic Lock Wiring Custom Bracket Magnetic Lock Plate Magnetic Lock Elite Part # A MG 1300 Gate Fence N.C. Common Power for Maglock Note: The optional relay
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 35
    /Second installation with overlapping gates. Opening "Inside" and Overlap to the "Outside"... Second Master operator delays to close the gate. Master Inside Property Opening "Inside" and Overlap to the "Inside"... Second Master operator delays to close the gate. 34 Master Inside Property
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 36
    a Master/Second installation with overlapping gates. Opening "Outside" and Overlap to the "Outside"... Master operator delays to close the gate. Second Master Inside Property Opening "Outside" and Overlap to the "Inside"... Master operator delays to close the gate. Second Master 35 Inside
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 37
    RELEASE Step 1: To move the gate during an emergency or power failure, insert key and turn counterclockwise to Unlock the Miracle 1 from the gate. Unlock Key Provided Step 2: Move the gate manually to the full open position 90°. Step 3: Re-Lock the operator by turning the key clockwise while
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 38
    TROUBLESHOOTING Check the Fuses If the gate is not moving in any direction be sure to check all of the LED displays on the control board. If the board power or charging power LEDs are on, change the corresponding fuse on the right side of the board. If the motor will not work, and all LED's on the
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 39
    TROUBLESHOOTING The Gate Will Not Close! For Toll Free Technical Support: 1-888-ELITE-10 Symptom: The radio receiver LED on CENTRAL the control board remains "ON" when using the remote control. CONTROL Possible Solutions: Stuck remote control button. The radio receiver has malfunctioned in the
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 40
    TROUBLESHOOTING You will SEE the alarm LED "ON" when... For Toll Free Technical Support: 1-888-ELITE-10 SYSOTNEM RSEEVNESROSRE SAELNASROMR Vertical Gate Level line Horizontal Gate Level line Incorrect Installation 1 The gate is too heavy or the operator or gate is installed incorrectly. 2 A
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 41
    11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 DC Power Adapter fits inside the Miracle-One electronic box DC Power Adapter Elite Part # A SOLAR ADP Contact your local dealer for more information. Connector from Miracle-One J1 Plug 40 Solar Panel Wires Battery Connector from Miracle-One
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 42
    Transmitter (Elite Part # A 1090) (Elite Part # Q240 MAU) Solar Panel (Elite Part # A 3089) 24V Photo Electric Eye (Elite Part # A OMRON) 24V DC External Loop Detectors (Elite Part # A 24) (Elite Part # A SOLAR 3) Outdoor Siren with Strobe Light (Elite Part # A SSA) DC Power Adapter (Elite Part
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 43
    POS STOP CLOSE DLY ON 3 POWER CHARGE OK BATTERY LOW ® ACCESS SYSTEMS INC CENTRAL CONTROL STRIKE OPEN SAFETY LOOP RADIO REC CENTER LOOP WRHEEPNLALCEEDFISUSOEN Q162 Q259 Q224 Q231 Q303 Q303 Q239 Q029 Accessories Q301 Q300 Q240 MAU Q242 A SOLAR ADP Note: Part names are on the next
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 44
    MIRACLE 1 PARTS LIST A BT MIR - Plastic Rack and 2 Batteries A POW3 - Transformer (24 VAC) A SOLAR ADP - DC Solar Power Adapter O-MIRACLE 1 ARM - Single Miracle 1 Arm (Complete) Q029 - Limit Switch (1) Q162 - 1.5 Amp Fuse Q222 - Control Board (Single Operator) Q223 - Control Board (Master/Second)
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 45
    44
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 46
    Input - Anti-tailgating system uses a "stop only" method of operation. Will not work as a commercial loop system. Alarm Output - Can be interfaced with any home alarm system. Alarm will sound if the gate is forced open manually. Optional siren can be installed. Spike Suppressors - Protected by
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 47
    1 Black 2 White 3 Red 4 Brown 5 Blue 6 Green Miracle 1 Master 7 Black 8 White 9 Red 10 Brown 11 Blue 12 Green 1 Black 2 White 3 Red 4 Brown 5 Blue 6 Green For Toll Free Technical Support: 1-888-ELITE-10 Refer to Page 31 Proximity Switch Normally Open Elite Part # A PRS 13 N.O. 14 Com 46
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 48
    Green Ground Wire The Miracle-One MUST be properly grounded. Please refer to the "Earth Ground Rod Installation" page 19. Refer to Page 20 24 VAC 40 VA Transformer Polarity does not matter 27 26 Refer to Page 21 24 VDC Radio Receiver Elite Part # A 1090 12 3 25 Radio Power 24 Relay ® 23
  • LiftMaster Miracle-One | MIRACLE ONE Manual - Page 49
    suggest the following items manufactured by Chamberlain Professional Products for better and safer operations. MG-1300 MAGNETIC LOCKS Offering up to 1300 pounds of holding force and an attached junction box. POWER HINGES Heavy duty industrial swing gate hinges for high traffic use. WARNING SIGNS Use
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49