Marantz MV8300 User Guide - Page 23

Marantz MV8300 Manual

Page 23 highlights

EN - Tracking Adjustments Automatic tracking adjustment This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback. 23 C Adjusting tracking condition D Selecting monitor sound - Audio Monitor You can select the desired monitor sound. While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote. Each time you press the button, sound changes as follows: S-VHS/VHS Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback, use the manual tracking following the procedures below. ● You can also use the manual tracking during slow motion playback (੬ pg. 33). During slow motion playback, simply press CHANNEL + or - on the VCR (or TV/VCR CH + or - on the Remote) to adjust tracking. LR MIX L R NORMAL 1 2 Activate manual tracking Press CHANNEL + and - on the front panel at the same time during playback. Eliminate the noises on the TV screen Press CHANNEL + or -. ● Press it briefly for a fine adjustment, or press and hold for a coarse adjustment. Watch the screen and continue adjustment until optimum picture and sound quality are achieved. ● To reactivate automatic tracking, press CHANNEL + and - on the front panel at the same time. The automatic tracking becomes active again. : Normally select this. Hi-Fi sound is played back. L: Sound on the left Hi-Fi channel is played back. Sound on the right Hi-Fi channel is played R : back. NORMAL: Sound on the normal track is played back. MIX: Both sounds on the Hi-Fi track and normal track are mixed and played back. LR D-VHS LR L R LR L: R : : Normally select this. Sound on the left channel is played back. Sound on the right channel is played back. NOTES: ● The above indication appears when "SUPERIMPOSE" is set to "ON" (੬ pg. 57), though the monitor sound changes in sequence. ● If the tape being played back has no Hi-Fi sound track, the normal sound track will be heard regardless of this setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88

EN
23
Selecting monitor sound
Audio Monitor
You can select the desired monitor sound.
While playing back a tape on which stereo sound or SAP
sound is recorded, press A. MONITOR on the Remote.
Each time you press the button, sound changes as follows:
S-VHS/VHS
L R
:
Normally select this.
Hi-Fi sound is played back.
L:
Sound on the left Hi-Fi channel is played
back.
R
:
Sound on the right Hi-Fi channel is played
back.
NORMAL: Sound on the normal track is played back.
MIX:
Both sounds on the Hi-Fi track and
normal track are mixed and played back.
D-VHS
L R
:
Normally select this.
L:
Sound on the left channel is played back.
R
:
Sound on the right channel is played back.
NOTES:
The above indication appears when
SUPERIMPOSE
is set to
ON
(
±
pg. 57), though the monitor sound changes in
sequence.
If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
C
NORMAL
MIX
L R
L
R
D
L R
L
R
Adjusting tracking condition
Tracking Adjustments
Automatic tracking adjustment
This VCR automatically adjusts the tracking condition.
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, use the manual tracking following the
procedures below.
You can also use the manual tracking during slow
motion playback (
±
pg. 33). During slow motion
playback, simply press
CHANNEL
+
or
on the VCR
(or
TV/VCR CH +
or
on the Remote) to adjust
tracking.
1
Activate manual tracking
Press
CHANNEL
+
and
on the front panel at the
same time during playback.
2
Eliminate the noises on the TV screen
Press
CHANNEL +
or
.
Press it briefly for a fine adjustment, or press and
hold for a coarse adjustment. Watch the screen
and continue adjustment until optimum picture
and sound quality are achieved.
To reactivate automatic tracking, press
CHANNEL
+
and
on the front panel at the same time. The
automatic tracking becomes active again.