Marantz PM-11S1 PM-11S1 User Manual - Page 14

Rear Panel

Get Marantz PM-11S1 PDF manuals and user guides View all Marantz PM-11S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

NAMES AND FUNCTIONS OF PARTS REAR PANEL 3 2 1 3 2 1 AC IN ENGLISH A PHONO GND Terminal Connect the grounding wire from an analog record player here. B PHONO Input Jacks These jacks are for connecting to an analog record player. Both MC and MM cartridges can be used, therefore set the PHONO MC button on the front panel according to the type of cartridge you are using. In the bi-amp mode, the R channel jack cannot be used. C BALANCED INPUT Jacks These jacks are for connecting to the balanced output jacks of a CD player or D/A converter. With the BALANCED INPUT jacks of the PM-11S1, pin 1 is GND, pin 2 is Cold and pin 3 is Hot. In the bi-amp mode, the R channel jack cannot be used. D CD Input Jacks These jacks are for connecting to the output jacks of a Super Audio CD player, CD player, etc. In the bi-amp mode, the R channel jack cannot be used. E LINE 1/2 Input Jacks These jacks are for connecting to the output jacks of a tuner, DVD player, etc. In the bi-amp mode, the R channel jack cannot be used. F RECORDER 1/2 IN Jacks These jacks are for connecting to the output jacks of a CDR, MD deck, tape deck, etc. In the bi-amp mode, the R channel jack cannot be used. G RECORDER 1/2 OUT Jacks These jacks are for connecting to the recording input jacks of a CD-R, MD deck, tape deck, etc. Output signals can be turned ON/OFF from the REC OUT button on the front panel. In the bi-amp mode, the signals input to the L channel are output to both output jacks. 10 H PREOUT Jacks These jacks are for connecting to the input jacks of another main amplifier or active subwoofer. Output signals can be turned ON/OFF from the PRE OUT button on the front panel. In the bi-amp mode, the signals input to the L channel are output to both output jacks. I SPEAKER SYSTEMS Output Terminals You can connect 2 speaker systems to the PM-11S1. Speaker output can be turned ON/OFF from the SPEAKER A and B buttons on the front panel. In the bi-amp mode, the signals input to the L channel are output to both output terminals. J F.C.B.S. IN/OUT Jacks You can connect and synchronize up to four PM-11S1s in a complete bi-amp connection or multi-channel connection. A stereo miniplug or monaural miniplug cable can be used for the connections. For instructions on use and connections, see "ABOUT FCBS" on pg. 15. K Operating Mode Switch This switch is for setting the operating mode of the PM11S1. STEREO: Set to use the PM-11S1 as an ordinary 2-channel stereo amplifier. BI-AMP: Set to use two PM-11S1s in a complete bi-amp connection with FCBS. For more information on the bi-amp mode, see "ABOUT THE BI-AMP MODE" on pg. 15. L AC IN Socket Connect one end of the included power cable here and the other end to a power outlet. The PM-11S1 can be powered by 120V AC only.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
10
ENGLISH
REAR PANEL
NAMES AND FUNCTIONS OF PARTS
A
PHONO GND Terminal
Connect the grounding wire from an analog record player
here.
B
PHONO Input Jacks
These jacks are for connecting to an analog record player.
Both MC and MM cartridges can be used, therefore set
the PHONO MC button on the front panel according to the
type of cartridge you are using.
In the bi-amp mode, the R channel jack cannot be used.
C
BALANCED INPUT Jacks
These jacks are for connecting to the balanced output jacks
of a CD player or D/A converter. With the BALANCED IN-
PUT jacks of the PM-11S1, pin 1 is GND, pin 2 is Cold and
pin 3 is Hot.
In the bi-amp mode, the R channel jack cannot be used.
D
CD Input Jacks
These jacks are for connecting to the output jacks of a
Super Audio CD player, CD player, etc.
In the bi-amp mode, the R channel jack cannot be used.
E
LINE 1/2 Input Jacks
These jacks are for connecting to the output jacks of a
tuner, DVD player, etc.
In the bi-amp mode, the R channel jack cannot be used.
F
RECORDER 1/2 IN Jacks
These jacks are for connecting to the output jacks of a CD-
R, MD deck, tape deck, etc.
In the bi-amp mode, the R channel jack cannot be used.
G
RECORDER 1/2 OUT Jacks
These jacks are for connecting to the recording input jacks
of a CD-R, MD deck, tape deck, etc. Output signals can be
turned ON/OFF from the REC OUT button on the front
panel.
In the bi-amp mode, the signals input to the L channel are
output to both output jacks.
H
PREOUT Jacks
These jacks are for connecting to the input jacks of an-
other main amplifier or active subwoofer. Output signals
can be turned ON/OFF from the PRE OUT button on the
front panel.
In the bi-amp mode, the signals input to the L channel are
output to both output jacks.
I
SPEAKER SYSTEMS Output Terminals
You can connect 2 speaker systems to the PM-11S1.
Speaker output can be turned ON/OFF from the SPEAKER
A and B buttons on the front panel.
In the bi-amp mode, the signals input to the L channel are
output to both output terminals.
J
F.C.B.S. IN/OUT Jacks
You can connect and synchronize up to four PM-11S1s in
a complete bi-amp connection or multi-channel connec-
tion. A stereo miniplug or monaural miniplug cable can be
used for the connections. For instructions on use and con-
nections, see
“
ABOUT FCBS
”
on pg. 15.
K
Operating Mode Switch
This switch is for setting the operating mode of the PM-
11S1.
STEREO: Set to use the PM-11S1 as an ordinary 2-chan-
nel stereo amplifier.
BI-AMP: Set to use two PM-11S1s in a complete bi-amp
connection with FCBS. For more information on the bi-amp
mode, see
“
ABOUT THE BI-AMP MODE
”
on pg. 15.
L
AC IN Socket
Connect one end of the included power cable here and
the other end to a power outlet. The PM-11S1 can be pow-
ered by 120V AC only.
AC IN
3
1
2
3
1
2