Marantz PM-11S1 PM-11S1 User Manual - Page 17
Basic Operation
View all Marantz PM-11S1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
BASIC OPERATION PLAYBACK To explain how to play back input sources, representative examples are given with an Super Audio CD player and analog record player. Before starting either procedure, check the component is correctly connected to the PM-11S1. 7 Disc Playback on an Super Audio CD Player 1. Press the power ON/OFF switch of the Super Audio CD player to activate power to it. 2. Press the POWER ON/OFF switch q of the PM-11S1 to activate power to it. Approximately 8 seconds after power has been activated, the muting turns OFF and audio output is enabled. When using multiple PM-11S1s connected by FCBS, turn power ON in the order of lowest to highest ID number, starting from ID 1. 3. Select the input source from the INPUT SELECTOR knob e on the PM-11S1 or the input selector buttons z of the remote controller. 4. To use the speakers connected to the SPEAKER A terminals, press the SPEAKER A button o on the PM11S1. 5. Load a disc into the Super Audio CD player and press the play button to start playback. 6. Adjust the volume level from the VOLUME knob r on the PM-11S1 or the VOLUME 3/4 buttons n of the remote controller. 7. Adjust bass/treble as desired from the TONE button i on the PM-11S1 or the TONE button v of the remote controller. For instructions on how to adjust bass and treble, see "How to Trim Bass" and "How to Trim Treble" on pg. 18. 8. You can turn the display and side illumination ON/OFF as suited for the room environment. Press the DISPLAY button u on the PM-11S1 or the DISPLAY button m of the remote controller. 7 Disc Playback on an Analog Record Player 1. Press the POWER ON/OFF switch q of the PM-11S1 to activate power to it. Approximately 8 seconds after power has been activated, the muting turns OFF and audio output is enabled. When using multiple PM-11S1s connected by FCBS, turn power ON in the order of lowest to highest ID number, starting from ID 1. 2. Select "PHONO" as the input source from the INPUT SELECTOR knob e on the PM-11S1 or the input selector buttons z of the remote controller. To prevent unexpected accidents, it is recommended to set the volume level to -∞ (mute) by turning the VOLUME knob r until muting the volume level. 3. Set the PHONO MC button !3 on the PM-11S1 to MC or MM according to the cartridge you are using. 4. To use the speakers connected to the SPEAKER A terminals, press the SPEAKER A button o on the PM11S1. 5. Set a record on the analog record player and play it. 6. Adjust the volume level from the VOLUME knob r on the PM-11S1 or the VOLUME 3/4 buttons n of the remote controller. 7. Adjust bass/treble as desired from the TONE button i on the PM-11S1 or the TONE button v of the remote controller. For instructions on how to adjust bass and treble, see "How to Trim Bass" and "How to Trim Treble" on pg. 18. 8. You can turn the display and side illumination ON/OFF as suited for the room environment. Press the DISPLAY button u on the PM-11S1 or the DISPLAY button m of the remote controller. INPUT SELECTOR DISPLAY TONE SPEAKER A SPEAKER B INTEGRARED AMPLIFIER PM-11S1 PHONES OPERATE POWER ON/OFF ATT. PRE OUT REC OUT PHONO MC VOLUME OPEN/ CLOSE SOUND MODE PHONO BALANCED CD RECORDER 1 LINE 1 RECORDER 2 TRIM EXIT LINE 2 TONE + L R ENTER DISPLAY - ATT VOLUME RANDOM SCAN REPEAT TOP MENU RETURN AM/A FM/B MENU RC-11PMS1 13 ENGLISH