Marantz PM-11S1 PM-11S1 User Manual - Page 23

How To Adjust Display Contrast, How To Set Id

Get Marantz PM-11S1 PDF manuals and user guides View all Marantz PM-11S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

ENGLISH HOW TO USE AND SET FEATURES HOW TO ADJUST DISPLAY CONTRAST An LCD is used as the PM-11S1's display. You can set the contrast in the +8 - -8 range. When the PM-11S1 is shipped from the factory, the contrast level is set to 0. The contrast adjustment mode is accessed by activating power from the POWER ON/OFF button while pressing and holding the DISPLAY button. Contrast is then set by turning the INPUT SELECTOR knob to the desired setting. 1. While pressing and holding the DISPLAY button, press the POWER ON/OFF button. HOW TO SET ID If using the PM-11S1 by itself as a stereo amplifier, set the ID to "0". When the PM-11S1 is shipped from the factory, the ID is set to "0". When the ID is set to a number other than "0", the PM11S1 cannot be used for standalone operation. The ID number of the PM-11S1 appears on the display for about 3 seconds after power is activated. 2. Turn the INPUT SELECTOR knob to the desired contrast setting. 3. When finished setting the display contrast, turn power to the PM-11S1 OFF. The setting is stored in memory and becomes active the next time power to the PM-11S1 I activated. INPUT SELECTOR knob DISPLAY button INPUT SELECTOR DISPLAY TONE SPEAKER A SPEAKER B INTEGRARED AMPLIFIER PM-11S1 PHONES OPERATE POWER ON/OFF POWER ON/OFF button When multiple PM-11S1s are connected, a unique ID number must be set for each one in order to distinguish between them. The PM-11S1 that centrally controls the other PM-11S1s takes ID 1. The PM-11S1 with ID 1 is called the "master". The other PM-11S1s that synchronize with the master are called "slaves" and take IDs "2" - "4". ID numbers must not be the same for any two units. Set ID numbers as follows. 1. While pressing and holding the DISPLAY button, press the POWER ON/OFF button. 2. Press the DISPLAY button once. 3. Turn the INPUT SELECTOR knob to the desired ID number. When finished setting the ID number, turn power to the PM11S1 OFF. The setting is stored in memory and becomes active the next time power to the PM-11S1 activated. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
19
ENGLISH
HOW TO ADJUST DISPLAY CONTRAST
An LCD is used as the PM-11S1
’
s display. You can set the
contrast in the +8 - -8 range. When the PM-11S1 is shipped
from the factory, the contrast level is set to 0. The contrast
adjustment mode is accessed by activating power from the
POWER ON/OFF button while pressing and holding the
DISPLAY button. Contrast is then set by turning the INPUT
SELECTOR knob to the desired setting.
1.
While pressing and holding the DISPLAY button, press the
POWER ON/OFF button.
2.
Turn the INPUT SELECTOR knob to the desired contrast
setting.
3.
When finished setting the display contrast, turn power to
the PM-11S1 OFF. The setting is stored in memory and
becomes active the next time power to the PM-11S1 I
activated.
HOW TO USE AND SET FEATURES
HOW TO SET ID
If using the PM-11S1 by itself as a stereo amplifier, set the ID
to
“
0
”
. When the PM-11S1 is shipped from the factory, the ID is
set to
“
0
”
.
When the ID is set to a number other than
“
0
”
, the PM-
11S1 cannot be used for standalone operation.
The ID number of the PM-11S1 appears on the display for
about 3 seconds after power is activated.
When multiple PM-11S1s are connected, a unique ID number
must be set for each one in order to distinguish between them.
The PM-11S1 that centrally controls the other PM-11S1s takes
ID 1. The PM-11S1 with ID 1 is called the
“
master
”
. The other
PM-11S1s that synchronize with the master are called
“
slaves
”
and take IDs
“
2
”
-
“
4
”
. ID numbers must not be the same for
any two units.
Set ID numbers as follows.
1.
While pressing and holding the DISPLAY button, press the
POWER ON/OFF button.
2.
Press the DISPLAY button once.
3.
Turn the INPUT SELECTOR knob to the desired ID number.
When finished setting the ID number, turn power to the PM-
11S1 OFF. The setting is stored in memory and becomes active
the next time power to the PM-11S1 activated.
INTEGRARED AMPLIFIER PM-11S1
POWER ON/OFF
PHONES
A
TONE
SPEAKER
B
SPEAKER
OPERATE
DISPLAY
SELECTOR
INPUT
INPUT SELECTOR knob
DISPLAY button
POWER ON/OFF button