Memorex MIHT5005 User Guide - Page 47

Troubleshooting Guide

Get Memorex MIHT5005 PDF manuals and user guides
UPC - 749720012299
View all Memorex MIHT5005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

TROUBLESHOOTING GUIDE Check the following before requesting service: SYMPTOM GENERAL No power. Power on, but unit not functioning properly. POSSIBLE CAUSE AC cord unplugged. Condensation has formed. Wrong type of CD inserted. Unit needs to be reset. POSSIBLE SOLUTION Plug the AC cord into an AC outlet. Unplug the unit and wait about one to two hours to allow the player to dry. This unit cannot play discs, other than shown on page 15. Press the Standby/Power button, then unplug the power cord. Wait one minute and then plug the unit back in. No picture. The disc is dirty or inserted incorrectly. Some features and functions are not available on all discs. The equipment is not connected properly. The INPUT of the TV is not set to receive the DVD signal output. The video cables are not securely connected. Clean disc and insert label side-up. This is normal; try another function. Connect the equipment according to the instructions in this manual. Select the appropriate video input mode, usually VIDEO or AV. Connect the video cables securely. No sound. The connected TV power is off. The equipment is not connected properly. The external equipment connected to the AUX IN jacks is not connected properly. Turn the TV on. Connect the equipment according to the instructions in this manual. Connect as per this manual, and press the AUX Mode button on the remote. Playback picture rolls. The playback picture is poor. The Search feature is not working. The picture is not fitting properly. The remote control is not working. The speaker cables are not securely connected. The external unit's power is off. Unit needs to be reset to NTSC. The disc is dirty. Some discs have sections that do not allow searching. Wrong menu option is selected in the SETUP MENU. The batteries are weak or dead. The batteries are not installed properly. The remote is not aimed at the sensor. Distance is too far or there is too much light in the room. There is an obstacle in the path of the beam. Connect the speaker cables securely. Turn the external unit on. Turn unit off and then back on to auto set it. Clean the disc. This is normal on some discs. Select the correct TV type (PS, LB, WIDE) which matches the TV you are using. Install fresh batteries. Install batteries according to the diagram. Aim the remote at the sensor. Operate within 20ft or reduce the light in the room. Move the obstacle. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
46
TROUBLESHOOTING GUIDE
Check the following before requesting service:
SYMPTOM
GENERAL
No power.
Power on, but unit not functioning
properly.
No picture.
No sound.
Playback picture rolls.
The playback picture is poor.
The Search feature is not working.
The picture is not fitting properly.
The remote control is not working.
POSSIBLE SOLUTION
Plug the AC cord into an AC outlet.
Unplug the unit and wait about one to
two hours to allow the player to dry.
This unit cannot play discs, other than
shown on page 15.
Press the Standby/Power button, then
unplug the power cord. Wait one minute
and then plug the unit back in.
Clean disc and insert label side-up.
This is normal; try another function.
Connect the equipment according to
the instructions in this manual.
Select the appropriate video input
mode, usually VIDEO or AV.
Connect the video cables securely.
Turn the TV on.
Connect the equipment according to
the instructions in this manual.
Connect as per this manual, and press
the AUX Mode button on the remote.
Connect the speaker cables securely.
Turn the external unit on.
Turn unit off and then back on to auto set it.
Clean the disc.
This is normal on some discs.
Select the correct TV type (PS, LB, WIDE)
which matches the TV you are using.
Install fresh batteries.
Install batteries according to the diagram.
Aim the remote at the sensor.
Operate within 20ft or reduce the light
in the room.
Move the obstacle.
POSSIBLE CAUSE
AC cord unplugged.
Condensation has formed.
Wrong type of CD inserted.
Unit needs to be reset.
The disc is dirty or inserted incorrectly.
Some features and functions are not
available on all discs.
The equipment is not connected properly.
The INPUT of the TV is not set to receive
the DVD signal output.
The video cables are not securely connected.
The connected TV power is off.
The equipment is not connected properly.
The external equipment connected to the
AUX IN jacks is not connected properly.
The speaker cables are not securely
connected.
The external unit’s power is off.
Unit needs to be reset to NTSC.
The disc is dirty.
Some discs have sections that do not
allow searching.
Wrong menu option is selected in the
SETUP MENU.
The batteries are weak or dead.
The batteries are not installed properly.
The remote is not aimed at the sensor.
Distance is too far or there is too much
light in the room.
There is an obstacle in the path of the
beam.