NEC X981UHD External Control Codes - Page 8

Communication Format

Get NEC X981UHD PDF manuals and user guides View all NEC X981UHD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Communication Format Header Message Check Code Delimiter The command packet consists of four parts, Header, Message, Check code and Delimiter. Recommended sequence of a typical procedure to control a monitor is as follows, [A controller and a monitor, two-way communication composition figure] ■ For the general command (see the part "6.3. Operation Code (OP code) Table") Controller Monitor Get Parameter Header Message Check Code Delimiter Get Parameter Reply Header Message Check Code Delimiter Set Parameter Header Message Check Code Delimiter Set Parameter Reply Header Message Check Code Delimiter Get Parameter Header Message Check Code Delimiter Get Parameter Reply Header Message Check Code Delimiter Save Current Setting Command Header Message Check Code Delimiter Save Current Setting Command Reply Header Message Check Code Delimiter The controller sends command to get a value from the monitor that you want to change. The monitor replies a current value of the requested item. The controller sends commands to set an adjusted value. The monitor replies to the controller for confirmation. The controller sends command to get a value for confirmation. The monitor replies an adjusted value. The controller requests to store the adjusted value to the monitor. The monitor replies to the controller for confirmation. ■ For the special command (see the part 7 to 23. and 5.5.2) Controller Header Command Message Check Code Delimiter Header Command Reply Message Check Code Delimiter Monitor The control does not suitable for above fixed protocol; use the proper command for each control. Please refer section 5.5 and section 7 to 23. The monitor replies a proper message defined for each control. (8/130)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
(8/130)
4. Communication Format
The command packet consists of four parts, Header, Message, Check code and Delimiter.
Recommended sequence of a typical procedure to control a monitor is as follows,
[A controller and a monitor, two-way communication composition figure]
■ For the general command (see the part "6.3. Operation Code (OP code) Table”)
■ For the special command (see the part 7 to 23. and 5.5.2)
Header
Message
Check Code
Delimiter
Monitor
Controller
Header
Message
Check Code
Delimiter
Get Parameter
Get Parameter Reply
Set Parameter
Set Parameter Reply
Get Parameter Reply
Save Current Setting Command
Get Parameter
The controller sends command to
get a value from the monitor that
you want to change.
The monitor replies a current value
of the requested item.
The controller sends commands to
set an adjusted value.
The
monitor
replies
to
the
controller for confirmation.
The controller sends command to
get a value for confirmation.
The monitor replies an adjusted
value.
The controller requests to store
the adjusted value to the monitor.
Command
Command Reply
The control does not suitable for
above fixed protocol; use the
proper command for each control.
Please refer section 5.5 and
section 7 to 23.
The monitor replies a proper
message defined for each control.
Save Current Setting Command Reply
The
monitor
replies
to
the
controller for confirmation.
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter
Monitor
Controller
Header
Message
Check Code
Delimiter
Header
Message
Check Code
Delimiter