NEC X981UHD External Control Codes - Page 91

Auto ID Complete

Get NEC X981UHD PDF manuals and user guides View all NEC X981UHD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

17.2 Auto ID Complete This command is used in order to notify complete status of Auto ID. 1) The monitor sends the controller to complete status of Auto ID. Header SOH-'0'-Monitor ID'0'-'A'-'0'-'C' Message STX-'C'-'A'-'0'-'A'-'0'-'2'-ST-MON-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'C'(30h,43h): Message length (12byte) Message STX (02h): Start of Message 'C'-'A'-'0'-'A'-'0'-'2' (43h, 41h, 30h, 41h, 30h, 32h): Auto ID '0'-'2' (30h,32h): Complete ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) MON: DETECTED MONITORS 01h (30h, 31h) - 64h (36h, 34h) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet 2) The controller replies to the monitor. Header SOH-'0'-'0'-Monitor ID'B'-'0'-'A' Message STX-'C'-'B'-'0'-'A'-'0'-'2'-ST-ETX Check code BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID. Ex.) When this byte is set to 'A', replying monitor's ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte) Message STX (02h): Start of Message 'C'-'B'-'0'-'A' (43h, 42h, 30h, 41h): Auto ID Reply Command '0'-'2' (30h,32h): Complete ST : Error Status No Error : 00h (30h, 30h) *Fixed ETX (03h): End of Message (91/130)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
(91/130)
17.2 Auto ID Complete
This command is used in order to notify complete status of Auto ID.
1) The monitor sends the controller to complete status of Auto ID.
Header
Message
Check code
Delimiter
SOH-'0'-Monitor ID-
'0'-'A'-'0'-'C'
STX-'C'-'A'-'0'-'A'-'0'-'2'-ST-MON-ETX
BCC
CR
Header
SOH (01h): Start of Header
'0' (30h): Reserved
Monitor ID: Specify the Monitor ID of which you want to change a setting.
Ex.) If Monitor ID is '1', specify 'A'.
'0' (30h): Message sender is the controller.
'A' (41h): Message type is "Command".
'0'-'C'(30h,43h): Message length (12byte)
Message
STX (02h): Start of Message
'C'-'A'-'0'-'A'-'0'-'2' (43h, 41h, 30h, 41h, 30h, 32h): Auto ID
'0'-'2' (30h,32h): Complete
ST: Error Status
No Error : 00h (30h, 30h)
Error
: 01h (30h, 31h)
MON: DETECTED MONITORS
01h (30h, 31h) - 64h (36h, 34h)
ETX (03h): End of Message
Check code
BCC: Block Check Code
Refer to the section 4.3 “Check code” for a BCC calculation.
Delimiter
CR (0Dh): End of packet
2) The controller replies to the monitor.
Header
Message
Check code
Delimiter
SOH-'0'-'0'-Monitor ID-
'B'-'0'-'A'
STX-'C'-'B'-'0'-'A'-'0'-'2'-ST-ETX
BCC
CR
Header
SOH (01h): Start of Header
'0' (30h): Reserved
'0' (30h): Message receiver is the controller.
Monitor ID: Indicate a replying Monitor ID.
Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’.
'B' (42h): Message type is "Command reply".
'0'-'A'(30h,41h): Message length (10byte)
Message
STX (02h): Start of Message
'C'-'B'-'0'-'A' (43h, 42h, 30h, 41h): Auto ID Reply Command
'0'-'2' (30h,32h): Complete
ST : Error Status
No Error : 00h (30h, 30h) *Fixed
ETX (03h): End of Message