Home » Netgear Manuals » Bridges & Routers » Netgear AX6600 » Manual Viewer

Netgear AX6600 User Manual - Page 75

Set up a bridge for a port group or VLAN tag group, Set up a bridge for a port group

Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Nighthawk AX8 8-Stream Tri-Band WiFi 6 Router 7. Select an IP address setting: • Get dynamically from existing router. The other router on the network assigns an IP address to this router while it is in AP mode. • Use fixed IP settings on this device (not recommended). Use this setting if you want to manually assign a specific IP address to this router while it is in AP mode. Using this option effectively requires advanced network experience. Note: To avoid interference with other routers or gateways in your network, we recommend that you use different WiFi settings on each router. You can also turn off the WiFi radio on the other router or gateway and use this router only for WiFi client access. 8. Click the Apply button. The IP address of the router changes, and you are disconnected. 9. To reconnect, close and restart your browser and type http://www.routerlogin.net. Set up a bridge for a port group or VLAN tag group Some devices, such as an IPTV, cannot function behind the router's network address translation (NAT) service or firewall. Based on what your Internet service provider (ISP) requires, for the device to connect to the ISP's network directly, you can enable the bridge between the device and the router's Internet port or add new VLAN tag groups to the bridge. Note: If your ISP provides instructions for how to set up a bridge for IPTV and Internet service, follow those instruction. Set up a bridge for a port group If the devices that are connected to the router's Ethernet LAN port or WiFi network include an IPTV device, your ISP might require you to set up a bridge for a port group for the router's Internet interface. A bridge with a port group prevents packets that are sent between the IPTV device and the router's Internet port from being processed through the router's network address translation (NAT) service. Manage Network Settings 75 User Manual

Section	Page
Contents	3
1. Hardware Setup	9
Unpack your router	10
Top panel LEDs and buttons	11
Rear panel	13
Extend the antennas	14
Router label	14
Position your router	15
Wall mount your router	16
Cable your router	17
2. Connect to the network and access the router	18
Connect to the network	19
Connect to the network using a wired connection	19
Find and connect to the WiFi network	19
WiFi connection using WPS	19
Types of logins	20
Install and manage your router with the Nighthawk app	20
Use a web browser to access the router	21
Automatic Internet Setup	21
Log in to the router	22
Change the language	23
3. Specify Your Internet Settings	24
Use the Internet Setup Wizard	25
Manually set up the Internet connection	25
Specify an Internet connection without a login	25
Specify an Internet connection that uses a login	27
Get Multi-Gig Internet with Internet port aggregation	29
Specify IPv6 Internet connections	30
Requirements for entering IPv6 addresses	31
Use auto detect for an IPv6 Internet connection	31
Set up an IPv6 6to4 tunnel Internet connection	32
Set up an IPv6 pass-through Internet connection	33
Set up an IPv6 fixed Internet connection	34
Set up an IPv6 DHCP Internet connection	36
Set up an IPv6 PPPoE Internet connection	37
Use auto config for an IPv6 Internet connection	39
Set up an IPv6 6rd Internet connection	40
Manage the MTU size	42
MTU concepts	42
Change the MTU size	43
4. Control Access to the Internet	45
Manage NETGEAR Armor	46
Activate Armor using the Nighthawk app	46
View or change your NETGEAR Armor settings using the Nighthawk app	46
Enable access control to allow or block access to the Internet	47
Use keywords to block Internet sites	48
Delete keywords from the blocked list	49
Block services from the Internet	50
Prevent blocking on a trusted computer	51
Manage network access control lists	52
Schedule when to block Internet sites and services	52
Set up security event email notifications	53
5. Manage Network Settings	55
View or change the WAN settings	56
Set up a default DMZ server	57
Change the Router’s Device Name	58
Change the LAN TCP/IP settings	58
Specify the IP addresses that the router assigns	60
Disable the DHCP server feature in the router	61
Manage reserved LAN IP addresses	62
Reserve an IP address	62
Edit a reserved IP address	63
Delete a reserved IP address entry	63
Use the WPS Wizard for WiFi connections	64
Specify basic WiFi settings	65
Change the WiFi mode	66
Change the WiFi password or the WiFi security	67
Set up a guest WiFi network	69
Control the WiFi radios	71
Use the WiFi On/Off button	72
Enable or disable the WiFi radios	72
Set up a WiFi schedule	72
Specify WPS settings	73
Set up the router as a WiFi access point	74
Set up a bridge for a port group or VLAN tag group	75
Set up a bridge for a port group	75
Set up a bridge for a VLAN tag group	76
Set up an IPTV port	78
Manage custom static routes	79
Set up a static route	80
Edit a static route	81
Delete a static route	81
Enable or disable airtime fairness	82
Enable or disable MU-MIMO	83
Enable or disable PMF	83
Set up the router in bridge mode	84
Manage Ethernet port aggregation to a LAN device	86
Set up Ethernet port aggregation to a LAN device	86
View or change the router Ethernet port aggregation mode	88
6. Optimize Performance	90
Use Dynamic QoS to optimize Internet traffic management	91
Enable Dynamic QoS	91
Enable or disable the automatic QoS database update	92
Manually update the dynamic QoS database	92
Improve network connections with Universal Plug and Play	93
Wi-Fi Multimedia Quality of Service	94
Enable or disable AX WiFi	95
Enable or disable Smart Connect	96
7. Manage Your Router	98
Update the router firmware	99
Check for new firmware and update the router	99
Manually upload firmware to the router	100
Change the admin password	101
Enable admin password recovery	101
Recover the admin password	102
View information about the router and the Internet and WiFi settings	103
Display the statistics of the Internet port	104
Check the Internet connection status	105
View and manage logs of router activity	106
View devices currently on the network	107
Monitor Internet traffic	107
Manage the router configuration file	109
Back up the settings	109
Erase the settings	109
Restore the settings	110
Manage remote access	111
Set up remote management	111
Use remote access	112
Connect to your router with Anywhere Access	112
Disable LED blinking or turn off LEDs	113
Set your time zone	113
Set the NTP Server	114
Specify ReadyDLNA Media Server Settings	115
Return the router to its factory default settings	116
Use the Reset button	116
Erase the settings	116
8. Share USB Storage Devices Attached to the Router	118
USB device requirements	119
Connect a USB storage device to the router	119
Access a storage device connected to the router from a Windows-based computer	120
Map a USB device to a Windows network drive	120
Access a storage device that is connected to the router from a Mac	121
Back up Windows-based computers with ReadySHARE Vault	122
Back up Mac computers with Time Machine	122
Set up a USB hard drive on a Mac	123
Prepare to back up a large amount of data	124
Use Time Machine to back up onto a USB hard disk	124
Enable FTP access within your network	126
View network folders on a storage device	126
Add a network folder on a USB storage device	127
Edit a network folder on a USB storage device	128
Safely remove a USB storage device	129
9. Use Dynamic DNS to Access USB Storage Devices Through the Internet	130
Set up and manage Dynamic DNS	131
Set up FTP access through the Internet	131
Your personal FTP server	132
Set up your personal FTP server	132
Set up a new Dynamic DNS account	133
Specify a DNS account that you already created	133
Change the Dynamic DNS settings	134
Access USB storage devices through the Internet	135
10. Use VPN to Access Your Network	136
Set up a VPN connection	137
Specify VPN service in the router	137
Install OpenVPN software	138
Install OpenVPN Software on Your Windows Computer	138
Install OpenVPN software on your Mac computer	141
Install OpenVPN software on an iOS device	142
Install OpenVPN software on an Android device	142
Use a VPN tunnel on your Windows computer	143
Use VPN to access the router’s USB device and media	145
Use VPN to access your Internet service at home	145
Set up VPN client Internet access in the router	146
Block VPN client Internet access in the router	146
Use a VPN tunnel to access your Internet service at home	147
11. Use a VPN client to connect to a VPN server	149
Set up a VPN client	150
Enable a VPN client	150
View your VPN connection status	151
View VPN client longs	152
12. Manage port forwarding and port triggering	153
Manage port forwarding to a local server	154
Set up port forwarding to a local server	154
Add a custom port forwarding service	155
Edit a port forwarding service	156
Delete a port forwarding entry	157
Application xxample: Make a local web server public	157
How the router implements the port forwarding rule	158
Port triggering	158
Add a port triggering service	159
Enable port triggering	160
Application example: Port triggering for Internet relay chat	160
13. Troubleshooting	162
Quick tips	163
Sequence to restart your network	163
Check the power adapter and Ethernet cable connections	163
Check the WiFi settings	163
Check the network settings	163
Troubleshoot with the LEDs	164
Standard LED behavior when the router is powered on	164
Power LED is off or blinking	164
LEDs never turn off	164
Internet or Ethernet LAN port LEDs are off	165
WiFi LED is off	165
You cannot log in to the router	165
You cannot access the Internet	166
Troubleshoot Internet browsing	168
Changes are not saved	168
Troubleshoot WiFi connectivity	169
Troubleshoot your network using the ping utility	169
Test the LAN path to your router	169
Test the path from a Windows-based computer to a remote device	170
14. Supplemental Information	172
Factory settings	173

Match case Limit results 1 per page

Select an IP address setting:

•

Get dynamically from existing router

. The other router on the network assigns

an IP address to this router while it is in AP mode.

•

Use fixed IP settings on this device (not recommended)

. Use this setting if you

want to manually assign a specific IP address to this router while it is in AP mode.

Using this option effectively requires advanced network experience.

Note:

To avoid interference with other routers or gateways in your network, we

recommend that you use different WiFi settings on each router. You can also turn

off the WiFi radio on the other router or gateway and use this router only for WiFi

client access.

Click the

Apply

button.

The IP address of the router changes, and you are disconnected.

To reconnect, close and restart your browser and type

http://www.routerlogin.net

Set up a bridge for a port group or VLAN tag

group

Some devices, such as an IPTV, cannot function behind the router’s network address

translation (NAT) service or firewall. Based on what your Internet service provider (ISP)

requires, for the device to connect to the ISP’s network directly, you can enable the

bridge between the device and the router’s Internet port or add new VLAN tag groups

to the bridge.

Note:

If your ISP provides instructions for how to set up a bridge for IPTV and Internet

service, follow those instruction.

Set up a bridge for a port group

If the devices that are connected to the router’s Ethernet LAN port or WiFi network

include an IPTV device, your ISP might require you to set up a bridge for a port group

for the router’s Internet interface.

A bridge with a port group prevents packets that are sent between the IPTV device and

the router’s Internet port from being processed through the router’s network address

translation (NAT) service.

User Manual

Manage Network Settings

Nighthawk AX8 8-Stream Tri-Band WiFi 6 Router