Nikon 9237 User Manual - Page 33

Step 1 - Turn the Scanner

Get Nikon 9237 - Super Coolscan 9000 ED PDF manuals and user guides
UPC - 018208092376
View all Nikon 9237 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Step 1-Turn the Scanner On Before turning on the scanner for the first time, make sure that Nikon Scan is installed on the computer and that the power and IEEE 1394 cables are connected. For information on installing Nikon Scan and connecting the cables, see "Setup" ( 7). 1 Turn the computer on Turn the computer on and wait for the operating system to start up. 2 Turn the scanner on The status LED will blink for about two minutes while the scanner initializes. The status LED will stop blinking when initialization is complete. Scanner off Scanner on Status LED off Status LED blinks Status LED on Windows 98 SE If the dialog shown at right appears the first time the scanner is connected and turned on, the IEEE 1394 driver update has not been completed. Update the IEEE 1394 drivers as described in "Updating the IEEE 1394 Drivers (Windows 98 SE Only): The 'Insert Disk' Dialog" ( 65). Windows 2000 Professional A "Digital Signature Not Found" dialog will be displayed the first time the scanner is connected and turned on following installation of Nikon Scan. Click Yes to register the scanner with Windows. If the Status LED Flickers If the status LED flashes quickly (about five times a second), turn the scanner off, wait at least five seconds, and turn the scanner on again. If the problem persists, see "Troubleshooting" ( 63). 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
24
Windows 98 SE
If the dialog shown at right appears the first time the scanner is
connected and turned on, the IEEE 1394 driver update has not been
completed.
Update the IEEE 1394 drivers as described in “Updat-
ing the IEEE 1394 Drivers (Windows 98 SE Only): The ‘Insert Disk’
Dialog”
(
65).
Windows 2000 Professional
A “Digital Signature Not Found” dialog will be displayed the first
time the scanner is connected and turned on following installation
of Nikon Scan.
Click
Yes
to register the scanner with Windows.
Step 1 — Turn the Scanner On
Step 1 — Turn the Scanner On
Before turning on the scanner for the first time, make sure that Nikon Scan is installed on the
computer and that the power and IEEE 1394 cables are connected.
For information on install-
ing Nikon Scan and connecting the cables, see “Setup” (
7).
1
Turn the computer on
Turn the computer on and wait for the operating system to start up.
2
Turn the scanner on
The status LED will blink for about two minutes while the scanner initializes.
The status
LED will stop blinking when initialization is complete.
Scanner off
Status LED off
Scanner on
Status LED blinks
Status LED on
If the Status LED Flickers
If the status LED flashes quickly (about five times a second), turn the scanner off, wait at least five sec-
onds, and turn the scanner on again.
If the problem persists, see “Troubleshooting” (
63).