Nikon 9237 User Manual - Page 35

FH-835S Holder for 35-mm Film, Inserting Film

Get Nikon 9237 - Super Coolscan 9000 ED PDF manuals and user guides
UPC - 018208092376
View all Nikon 9237 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2 Place film in the holder FH-835S Holder for 35-mm Film The FH-835S can be used with one or two strips of 35-mm film. Each strip can be up to six frames long. 2.1 Open the holder Insert your fingers through the holes in the bottom half of the holder and undo the latches, then open the holder. Latches 2.2 Insert film Place film in the holder with the reflective film base up and the matte emulsion surface down. Arrow Inserting Film Align the first frame in each strip with an aperture at the left end of the holder. Leaving the apertures at the left end of the holder uncovered or covering them with a masking sheet could cause scanning errors or interfere with accurate color reproduction. Use only one type of film; do not mix negatives with positive film. Direction of insertion Thumbnails displayed in order shown Inserting Film Do not place film or masking sheets so that they protrude from the holder or overlap the film guides. Failure to observe this precaution could cause the holder to jam in the scanner. "Film Base"/"Emulsion Surface" When film is examined under bright light, the image on the emulsion surface will be in slight relief, with bumps and hollows where the image has been developed. The opposite surface (the film base) will be reflective and smooth. Insert film with the base up. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
26
2
Place film in the holder
FH-835S Holder for 35-mm Film
The FH-835S can be used with one or two strips of 35-mm film.
Each strip can be up to
six frames long.
2.1
Open the holder
Insert your fingers through the holes
in the bottom half of the holder and
undo the latches, then open the
holder.
Latches
2.2
Insert film
Place film in the holder with the reflec-
tive film base up and the matte emulsion
surface down.
Inserting Film
Align the first frame in each strip with
an aperture at the left end of the hold-
er.
Leaving the apertures at the left
end of the holder uncovered or cover-
ing them with a masking sheet could
cause scanning errors or interfere with
accurate color reproduction.
Use only one type of film; do not mix
negatives with positive film.
Inserting Film
Do not place film or masking sheets so that they protrude from the holder or overlap the film guides.
Failure to observe this precaution could cause the holder to jam in the scanner.
“Film Base”/”Emulsion Surface”
When film is examined under bright light, the image on the emulsion surface will be in slight relief, with
bumps and hollows where the image has been developed.
The opposite surface (the film base) will be
reflective and smooth.
Insert film with the base up.
Direction of
insertion
Thumbnails
displayed in
order shown
Arrow