Olympus D-510 Zoom D-510 Zoom Instruction Manual - Page 148

Troubleshooting (Check before Taking in for Repair), Operating Problems

Get Olympus D-510 Zoom PDF manuals and user guides View all Olympus D-510 Zoom manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Troubleshooting (Check before Taking in for Repair) Operating Problems The camera does not work • The power is off. ➜ Open the lens barrier and turn on the power. • The batteries are loaded incorrectly. ➜ Reload the batteries correctly. • The batteries are dead. ➜ Replace with new batteries. • The card cover is not properly closed. ➜ Securely close the card cover. • The batteries do not work in to cold weather. ➜ Keep the batteries warm before the camera is to be used. • The standby function is on. ➜ Close the lens barrier, then reopen it. • The camera is connected to a computer and does not work. ➜ The camera will not function while connected to a computer. Disconnect the camera. The battery drains quickly • The battery was left in the camera for a long period of time without using the camera. ➜ Remove the battery if you do not intend to use the camera for a long period of time. • The monitor is being left on continuously while shooting. ➜ Make efforts to turn the monitor off in between shots whenever possible. No picture is taken when the shutter button is full-pressed • The camera is not in record mode. ➜ Open the lens barrier. • There is no card in the camera. ➜ Insert a new card into the camera. • The card is full. ➜ Insert a new card, erase unwanted images or transfer the data to a computer and delete all of the pictures from the card. • The card is defective. ➜ Refer to the error chart. • A write-protect seal has been placed on the card. ➜ Remove the write-protect seal, or insert a new card into the camera. • The flash has not finished charging or the previous picture is being written to memory. ➜ Remove your finger from the shutter button and wait until the green lamp or the orange lamp stops blinking. • The memory gauge is illuminated. ➜ The camera's internal memory is full. Further shooting will only be possible if the memory gauge is no longer illuminated. • The memory gauge is illuminated after movie shooting. ➜ The movie pictures taken are being written to the card. Wait until the memory gauge is off. • The batteries are dead. ➜ Replace with new batteries. • The battery power is low. ➜ Replace with new batteries. (Do not open the battery compartment cover when the green light is blinking.) 138

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
138
Troubleshooting
(Check before Taking in for Repair)
Operating Problems
The camera does not work
• The power is off.
➜
Open the lens barrier and turn on the power.
• The batteries are loaded incorrectly.
➜
Reload the batteries correctly.
• The batteries are dead.
➜
Replace with new batteries.
• The card cover is not properly closed.
➜
Securely close the card cover.
• The batteries do not work in to cold weather.
➜
Keep the batteries
warm before the camera is to be used.
• The standby function is on.
➜
Close the lens barrier, then reopen it.
• The camera is connected to a computer and does not work.
➜
The
camera will not function while connected to a computer. Disconnect
the camera.
The battery drains quickly
• The battery was left in the camera for a long period of time without
using the camera.
➜
Remove the battery if you do not intend to use
the camera for a long period of time.
• The monitor is being left on continuously while shooting.
➜
Make
efforts to turn the monitor off in between shots whenever possible.
No picture is taken when the shutter button is full-pressed
• The camera is not in record mode.
➜
Open the lens barrier.
• There is no card in the camera.
➜
Insert a new card into the camera.
•
The card is full.
➜
Insert a new card, erase unwanted images or transfer
the data to a computer and delete all of the pictures from the card.
• The card is defective.
➜
Refer to the error chart.
• A write-protect seal has been placed on the card.
➜
Remove the
write-protect seal, or insert a new card into the camera.
• The flash has not finished charging or the previous picture is being
written to memory.
➜
Remove your finger from the shutter button and
wait until the green lamp or the orange lamp stops blinking.
• The memory gauge is illuminated.
➜
The camera’s internal memory is
full. Further shooting will only be possible if the memory gauge is no
longer illuminated.
• The memory gauge is illuminated after movie shooting.
➜
The movie
pictures taken are being written to the card. Wait until the memory
gauge is off.
• The batteries are dead.
➜
Replace with new batteries.
• The battery power is low.
➜
Replace with new batteries. (Do not open
the battery compartment cover when the green light is blinking.)