Olympus D-510 Zoom D-510 Zoom Instruction Manual - Page 149

Editing, Protection, One-Frame Erase, All Erase Frames, or Card Formatting does not function

Get Olympus D-510 Zoom PDF manuals and user guides View all Olympus D-510 Zoom manuals
Add to My Manuals
Save this manual to your list of manuals

Page 149 highlights

The flash does not fire • The flash is not fully opened. ➜ Use your finger to push the flash housing all the way up before resuming use. • The subject is well lit. ➜ Set the flash mode to Fill-in if you want the flash to fire regardless of lighting conditions. The flash does not work with shooting in the sequence, panorama, or movie picture modes. Pictures already taken do not appear on the monitor • The camera is in record mode. ➜ Close the lens barrier and press the monitor button ( ) to turn on the monitor in playback mode. • The SmartMedia card is empty. ➜ "NO PICTURE" appears on the monitor. Take some pictures before displaying. • The SmartMedia card is defective. ➜ Refer to the error chart. • The camera is connected to a television. ➜ The monitor shuts down when the camera is connected to a television. The monitor is hard to see • The brightness may be set incorrectly. ➜ Adjust the brightness. • The camera is in direct sunlight. ➜ Block the sunlight or move to the shade. Editing, Protection, One-Frame Erase, All Erase Frames or Card Formatting does not function • A write-protect seal has been placed on the card. ➜ Remove the seal from the card. Do not use the seal again. The camera is connected to a computer and an error message appears while data is being transferred • The cable may be connected incorrectly. ➜ Connect the cable correctly. • The batteries are dead. ➜ Replace the batteries, or use the optional AC adapter. • The USB driver has not been installed correctly. ➜ Reinstall the USB driver according by following the steps in the instructions. 139 Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
139
Appendix
The flash does not fire
• The flash is not fully opened.
➜
Use your finger to push the flash
housing all the way up before resuming use.
• The subject is well lit.
➜
Set the flash mode to Fill-in if you want the
flash to fire regardless of lighting conditions. The flash does not work
with shooting in the sequence, panorama, or movie picture modes.
Pictures already taken do not appear on the monitor
• The camera is in record mode.
➜
Close the lens barrier and press the
monitor button (
) to turn on the monitor in playback mode.
• The SmartMedia card is empty.
➜
“NO PICTURE” appears on the
monitor.Take some pictures before displaying.
• The SmartMedia card is defective.
➜
Refer to the error chart.
• The camera is connected to a television.
➜
The monitor shuts down
when the camera is connected to a television.
The monitor is hard to see
• The brightness may be set incorrectly.
➜
Adjust the brightness.
• The camera is in direct sunlight.
➜
Block the sunlight or move to the
shade.
Editing, Protection, One-Frame Erase, All Erase Frames
or Card Formatting does not function
• A write-protect seal has been placed on the card.
➜
Remove the seal
from the card. Do not use the seal again.
The camera is connected to a computer and an error
message appears while data is being transferred
• The cable may be connected incorrectly.
➜
Connect the cable
correctly.
• The batteries are dead.
➜
Replace the batteries, or use the optional
AC adapter.
• The USB driver has not been installed correctly.
➜
Reinstall the USB
driver according by following the steps in the instructions.