Panasonic 55 Professional Display for Entry-Level Digital Signage Operating In - Page 56

DIGITAL LINK status LF80 series only, AMX D.D.], DIGITAL LINK]

Get Panasonic 55 Professional Display for Entry-Level Digital Signage PDF manuals and user guides View all Panasonic 55 Professional Display for Entry-Level Digital Signage manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

● Even if [DIGITAL LINK mode] is set to [Long reach], when the twisted pair cable transmitter does not support the communication method of [Long reach], it will not be connected properly. ■■DIGITAL LINK status (LF80 series only) Display the DIGITAL LINK connection environment. Select [DIGITAL LINK status] with . and press DIGITAL LINK status LINK status HDMI status Signal quality Min Max No link No HDMI -XX dB -YY dB [LINK status]: 1 of the followings will be displayed. [No link]: No LAN connection, etc. [DIGITAL LINK]: Connected to the DIGITAL LINK device by LAN. [Long reach]: Communication method is set to [Long reach] and is connected to the DIGITAL LINK device by LAN. [Ethernet]: The PC is connected to the DIGITAL LINK / LAN terminal of this product and is LAN connected. [HDMI status]: 1 of the followings will be displayed. [No HDMI]: DIGITAL LINK not connected [HDMI ON]: DIGITAL LINK connected [HDCP ON]: HDCP supported on DIGITAL LINK [Signal quality]: It is the quantified minimum and maximum numbers of errors that have occurred. The display colours are red, yellow, or green, depending on the number. Signal quality -12dB or below -11 to -8dB -7dB or above Display Colours Green Yellow Red Reception Status Good Bad Terrible ● The number is represented by yellow or red if the LAN cable is disconnected or the cable is not shielded. ● This signal quality shows figures between the twisted pair cable transmitter that is connected and the display. ■■DIGITAL LINK menu (LF80 series only) Displays the setting menu of Digital Interface Box. Select [DIGITAL LINK menu] with . and press Note ● This function can only be selected when the Panasonic device that supports DIGITAL LINK output (ET-YFB100G, ET-YFB200G) is connected to a DIGITAL LINK / LAN terminal and its power is on. ● For details, refer to the manuals of the devices that support DIGITAL LINK output. ■■[AMX D.D.] Set whether to allow the Display to be detected by AMX Device Discovery. [On]: Enables detection by AMX Device Discovery. [Off]: Disables detection by AMX Device Discovery. ● For more details, visit the following web site. http://www.amx.com/ 56 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
English
56
●
Even if [DIGITAL LINK mode] is set to [Long
reach], when the twisted pair cable transmitter
does not support the communication method of
[Long reach], it will not be connected properly.
■
DIGITAL LINK status (LF80 series only)
Display the DIGITAL LINK connection environment.
Select [DIGITAL LINK status] with
and press
<ENTER>.
-YY dB
-XX dB
DIGITAL LINK status
LINK status
HDMI status
Signal quality
Min
Max
No link
No HDMI
[LINK status]:
1 of the followings will be displayed.
[No link]:
No LAN connection, etc.
[DIGITAL LINK]:
Connected to the DIGITAL LINK device by LAN.
[Long reach]:
Communication method is set to [Long reach] and is
connected to the DIGITAL LINK device by LAN.
[Ethernet]:
The PC is connected to the DIGITAL LINK / LAN
terminal of this product and is LAN connected.
[HDMI status]:
1 of the followings will be displayed.
[No HDMI]:
DIGITAL LINK not connected
[HDMI ON]:
DIGITAL LINK connected
[HDCP ON]:
HDCP supported on DIGITAL LINK
[Signal quality]:
It is the quantified minimum and maximum numbers
of errors that have occurred. The display colours are
red, yellow, or green, depending on the number.
Signal quality
Display
Colours
Reception
Status
-12dB or below
Green
Good
-11 to -8dB
Yellow
Bad
-7dB or above
Red
Terrible
●
The number is represented by yellow or red if
the LAN cable is disconnected or the cable is not
shielded.
●
This signal quality shows figures between the
twisted pair cable transmitter that is connected and
the display.
■
DIGITAL LINK menu (LF80 series only)
Displays the setting menu of Digital Interface Box.
Select [DIGITAL LINK menu] with
and press
<ENTER>.
Note
●
This function can only be selected when the
Panasonic device that supports DIGITAL LINK output
(ET-YFB100G, ET-YFB200G) is connected to a
DIGITAL LINK / LAN terminal and its power is on.
●
For details, refer to the manuals of the devices that
support DIGITAL LINK output.
■
[AMX D.D.]
Set whether to allow the Display to be detected by AMX
Device Discovery.
[On]:
Enables detection by AMX Device Discovery.
[Off]:
Disables detection by AMX Device Discovery.
●
For more details, visit the following web site.