Panasonic SCPT1050 SCPT1050 User Guide - Page 36

Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to "Customer Services Directory" on page 42 if you reside in the U.S.A., or refer to "Product information" on page 35 if you reside in Canada. In other areas, consult your dealer. Power No power. ≥ Insert the AC power supply cord securely. 10 The unit is automatically switched ≥ The Sleep timer was working and had reached the set time limit. 12 to standby mode. Unit displays The display is dark. "NOPLAY" "NODISC" "NO MIC" "NOISY" "F61" "F76" "DVD U11" "ERROR" "DVD H∑∑" "DVD F stands for a number. " [W1] " or " [WS] " is flashing. "U70∑" ∑ stands for a number. The actual number following "U70" will depend on the state of the main unit. "XM RADIO" "XM ERROR" "REMOTE 1" or "REMOTE 2" ≥ Select "Bright" in "FL Dimmer" in the "Others" menu. ≥ You inserted a disc the unit cannot play; insert one it can. ≥ You inserted a blank disc. ≥ You inserted a disc that has not been finalized. ≥ You have not inserted a disc; insert one. ≥ You have not inserted the disc correctly; insert it correctly. ≥ Ensure that the setup microphone is properly connected to the SETUP MIC terminal. ≥ The ambient noise is high. Perform the setup again and keep quiet during the auto speaker setup. ≥ Check and correct the speaker cable connections. If this does not fix the problem, consult the dealer. ≥ There is a power supply problem. Consult the dealer. ≥ Disc may be dirty. Wipe it clean. ≥ Incorrect operation performed. Read the instructions and try again. ≥ Ensure that necessary preparations have been made before Auto Speaker Setup. ≥ Check and correct the speaker cable connections if you are doing Auto Speaker Setup. ≥ The volume might be muted. Cancel muting before Auto Speaker Setup. ≥ Trouble may have occurred. The numbers following "H" and "F" depend on the status of the unit. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC power supply cord, and then reconnect it. ≥ If the service numbers fail to clear, note the service number and contact a qualified service person. ≥ There is no link between the main unit and the wireless equipment. Check that the wireless equipment is plugged into the AC outlet and is turned on. ≥ [PT1050] Ensure the pairing procedure for the wireless subwoofer is performed correctly. ≥ Ensure that the digital transmitter is fully inserted into the slot of the main unit. ≥ The HDMI connection acts unusually. - The connected equipment is not HDMI-compatible. - Please use HDMI cables that have the HDMI logo (as shown on the cover). - The HDMI cable is too long. - The HDMI cable is damaged. ≥ It takes a short time for the XM radio to power up after turning on the main unit, during which time "XM RADIO" is displayed (only when the selected source is XM). Wait a few seconds for this process to complete. ≥ There may be an error in the XM radio module. Turn the main unit off, and then back on. ≥ The XM antenna may be defective. Consult the dealer of the XM antenna. ≥ Match the modes on the main unit and remote control. Depending on the number being displayed ("1" or "2"), press and hold [ENTER] and the corresponding numbered button ([1] or [2]) for at least 2 seconds. 27 14 - - - 16 33 33 8 - 15 - 33 8 12 - - 10, 13 11 9 - - - - - - - 12 Troubleshooting guide General operation No response when any buttons ≥ This unit cannot play discs other than the ones listed in these operating instructions. 14 are pressed. ≥ The unit may not be operating properly due to lightning, static electricity or some other external - factor. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC power supply cord, and then reconnect it. ≥ Condensation has formed. Wait 1 to 2 hours for it to evaporate. - No response when remote control ≥ Check that the batteries are installed correctly. 11 buttons are pressed. ≥ The batteries are depleted. Replace them with new ones. 11 ≥ Aim the remote control at the remote control signal sensor and operate. 13 Other products respond to the ≥ Change the remote control operating mode. 12 remote control. Cannot play DVDs. ≥ CD Mode is on. Press [CD MODE] to turn CD Mode off. 18 No picture or sound. ≥ Check the video or speaker connection. 7, 8 ≥ Check the power or input setting of the connected equipment and the main unit. - ≥ Check that the disc has something recorded on it. - You have forgotten your ratings ≥ While stopped and "DVD/CD" is the source, press and hold [∫] (Stop) on the main unit and [S10] on - password. the remote control until "Initialized" disappears from the television. Turn the unit off and on again. Reset all the settings to Factory Preset. All settings will return to the default values. RQTX0064 The EZ Sync "HDAVI Control" ≥ Depending on the condition of the home theater system or the connected equipment, it may be 28 function does not respond. necessary to repeat the same operation so that the function can work correctly. 36 Cannot operate the television. ≥ Check the remote control code for the television manufacturer. 12