Pfaff performance 2058 Owner's Manual - Page 31

Turn off the on/off switch, To remove, To insert

Get Pfaff performance 2058 PDF manuals and user guides View all Pfaff performance 2058 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Preparations Changing the needle Turn off the on/off switch To remove: Lower the presser foot and set the needle to its highest position. Loosen the needle screw and pull down on the needle to remove. To insert: The flat side of the needle must face to the rear. Keep the presser foot down and insert the needle, pushing it up as far as it will go. Hold the needle and tighten the needle screw firmly. Threading the twin needle Turn off the on/off switch Replace the sewing needle with a twin needle. Insert the second spool pin and place one spool of thread on each of the spool pins. On the vertical spool pin, place a spool cap and a felt pad underneath the C spool of thread. When threading make sure to pass one thread to the left and one thread to the right side of tension disk C. Continue threading in the usual manner, making sure the threads do not twist together. Pull one thread into the right thread guide above the needle, and the other thread into the left. Thread the needles. Note: It is not possible to use the Integrated Needle Threader with a twin needle. 2:13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2:13
C
Preparations
Changing the needle
Turn off the on/off switch
To remove:
Lower the presser foot and set the needle to its highest
position. Loosen the needle screw and pull down on the needle to
remove.
To insert:
The
fl
at side of the needle must face to the rear. Keep the
presser foot down and insert the needle, pushing it up as far as it will
go. Hold the needle and tighten the needle screw
fi
rmly.
Threading the twin needle
Turn off the on/off switch
Replace the sewing needle with a twin needle. Insert the second spool
pin and place one spool of thread on each of the spool pins. On the
vertical spool pin, place a spool cap and a felt pad underneath the
spool of thread.
When threading make sure to pass one thread to the left and one
thread to the right side of tension disk C.
Continue threading in the usual manner, making sure the threads do
not twist together.
Pull one thread into the right thread guide above the needle, and the
other thread into the left. Thread the needles.
Note:
It is not possible to use the Integrated Needle Threader with a
twin needle.