Home » Ricoh Manuals » Scanners » Ricoh IS760 » Manual Viewer

Ricoh IS760 Operating Instructions - Page 27

Setting the SCSI ID Automatically - scanner manual

Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Connecting to the Computer Setting the SCSI ID Automatically Note ❒ If you use the SCSI board without SCAM function or the SCSI ID is overlapping with the other SCSI device, set the SCSI ID manually. A Open the cover of the switch box on the lower left of the frontside of the scanner. 2 ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. B Set the DIP Switch No.1 to the ON position. ADC016S SCAM function is enabled. 23

Section	Page
Image Scanner Operating Instructions	1
Introduction	2
Important	2
Caution	2
Power Source	2
Trademarks	2
TABLE OF CONTENTS	3
Safety Information	5
Safety During Operation	5
Energy Star Program	8
Manuals for This Scanner	9
How to Read This Manual	10
Symbols	10
1. Guide to Components	11
Guide to This Scanner	11
Understanding Indicators	13
DIP Switches	14
2. Setting up the Scanner	15
Confirmations Before the Setup	15
Location, Space and Environment	15
Disengaging the lock for transportation	17
Installing Options	20
Installing the Image-Processing Unit	20
Installing the IEEE1394 Interface Board	22
Connecting to the Computer	25
Connecting with SCSI Interface	25
About the SCSI Interface	25
Setting the SCSI ID	26
Setting the SCSI ID Automatically	27
Connecting the SCSI Cable (When the Scanner is at the End of the Daisy Chain)	28
Connecting the SCSI Cable (When the Scanner is not at the End of the Daisy Chain)	30
Using the Scanner only with the SCSI Connection	31
Connecting with USB Interface	32
Connecting with IEEE1394 Interface	33
Connecting to a Power Source	35
Turning the Power On/Off	37
Turning the Power On when Connected with SCSI Interface	37
Turning the Power On when Connected with USB/IEEE1394 Interface	37
Turning the Power Off	37
Using the Hard Reset Switch	38
3. Installing Software	39
Installing TWAIN Driver	39
System Requirements	39
Installing TWAIN Driver	40
Installing DeskTopBinder Lite	42
System Requirements	42
Installing DeskTopBinder Lite	43
Installing ISIS Driver	44
System Requirements	44
Installing ISIS Driver	45
Installing QuickScan	47
System Requirements	47
Installing QuickScan	47
4. Setting Originals	49
Sizes and Weights of Recommended Originals	49
Original Sizes Available for Auto Detection	50
Originals that Require Special Care	51
Placing Originals	52
Placing the Original on the Exposure Glass	52
Placing the Originals in the ADF	53
Changing the Color of the Background Panel	56
Changing the Color of the Background Panel for the ADF	56
Changing the Color of the Background Panel for the Exposure Glass	58
5. Using the TWAIN Driver	61
Procedure Breakdown	61
Scanning Originals	62
What You Can Do with the TWAIN Driver	64
Functions of the TWAIN Driver	64
6. Appendix	67
Troubleshooting	67
Error Indicators	67
When the Original is Jammed or Double Fed in the ADF	68
When the Originals are Not Fed Correctly	70
When Scanning is Not Performed as Expected	70
When an Error Message Appears	71
When in Installation and Other Problems	74
Cleaning	75
Cleaning the Original Table Cove	76
Cleaning Under the Pressure Panel	77
Cleaning Under the Background Panel	78
Cleaning Inside the ADF Cover	80
Cleaning the Ventilation Panel	81
Moving and Transporting the Scanner	82
Moving Over Short Distances	82
Transporting the Scanner	83
Disposing of the Scanner	85
How Data Size Changes Depending on Scan Area and Resolution	86
When [Binary(Text)], [Binary(Photo)], [Binary(Auto Image)], or [Binary(Text/Photo)] is Selected	86
When [Gray Scale] or [256 Colors] is Selected	87
When [8 Colors] or [8 Colors(Photo)] is Selected	87
When [16770K colors] is Selected	88
Options	89
Image Processing Unit Type B	89
IEEE1394 Interface Unit Type IS760	89
Specifications	90