Sharp HT-DD5000 HTDD5000 Operation Manual - Page 22

Sharp HT-DD5000 Manual

Get Sharp HT-DD5000 PDF manuals and user guides View all Sharp HT-DD5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

RADIO OPERATION 1 2,3,5,6 4 s Tuning 1 Set the POWER button on the main unit to ON. 2 Press the TUNER (BAND) button. 3 Press the TUNER (BAND) button again to select the de- sired frequency band. (FM ST, FM or AM) 4 Press the TUNING (UP or DOWN) button to tune into the desired station. Manual tuning: Press the TUNING (UP or DOWN) button as many times as required to adjust the frequency shown in the display to the frequency of the desired station. Auto tuning: When the TUNING (UP or DOWN) button is pressed for more than 0.5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: q When radio interference occurs during auto scan tuning, auto scan tuning may stop automatically at that point. q If a weak station signal is found during auto scan tuning, the station will be skipped. q To stop auto tuning, press the TUNING (UP or DOWN) button again. 5 To receive an FM stereo transmission, press the TUNER (BAND) button so that the "STEREO" indicator on the display lights up. j q " " will appear when an FM broadcast is in stereo. 6 If the FM reception is weak, press the TUNER (BAND) button so that the "STEREO" indicator goes out. q Although the reception changes to monaural, the sound becomes clearer. After use: Set the POWER button on the main unit to OFF. Notes: q The last station tuned in will be recalled, even after changing the tuning band or the function, or after turning the power off. q When listening to a radio station broadcasting monaural sound, select STEREO in the Dolby Surround mode. 21 HT-DD5000(SEC) TINSE0009SJZZ

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
RADIO OPERATION
■
Tuning
1
Set the POWER button on the main unit to ON.
2
Press the TUNER (BAND) button.
3
Press the TUNER (BAND) button again to select the de-
sired frequency band. (FM ST, FM or AM)
4
Press the TUNING (UP or DOWN) button to tune into
the desired station.
Manual tuning:
Press the TUNING (UP or DOWN) button as many times as
required to adjust the frequency shown in the display to the
frequency of the desired station.
Auto tuning:
When the TUNING (UP or DOWN) button is pressed for
more than 0.5 seconds, scanning will start automatically and
the tuner will stop at the first receivable broadcast station.
Notes:
●
When radio interference occurs during auto scan tuning,
auto scan tuning may stop automatically at that point.
●
If a weak station signal is found during auto scan tuning,
the station will be skipped.
●
To stop auto tuning, press the TUNING (UP or DOWN)
button again.
5
To receive an FM stereo transmission, press the TUNER
(BAND) button so that the "STEREO" indicator on the
display lights up.
●
"
" will appear when an FM broadcast is in stereo.
6
If the FM reception is weak, press the TUNER (BAND)
button so that the "STEREO" indicator goes out.
●
Although the reception changes to monaural, the sound
becomes clearer.
After use:
Set the POWER button on the main unit to OFF.
Notes:
●
The last station tuned in will be recalled, even after
changing the tuning band or the function, or after turning
the power off.
●
When listening to a radio station broadcasting monaural
sound, select STEREO in the Dolby Surround mode.
1
2,3,5,6
4
HT-DD5000(SEC) TINSE0009SJZZ
21