Sony FWD-50PX2 User Manual - Page 47

Control Mode is set to Display Unit

Get Sony FWD-50PX2 PDF manuals and user guides View all Sony FWD-50PX2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Troubleshooting Problem 7 The remote control does not work. Cause In the remote control settings, the "Control Mode" is set to "Display Unit Only". Remedy Using the control buttons on the top of the display, check the setting by opening the main menu and then selecting "CUSTOM SETUP" t "Remote" t "Control Mode". For details on the "Control Mode", see "Control Mode" on page 19 (GB). A cable is connected to the CONTROL S IN connector. Check the condition of the CONTROL S IN connector. The remote control cannot be used while the display is controlled via a Control S connection. The batteries in the remote control are Try operating the display by pressing the drained. power button and control buttons on the top of the display. Also, check the condition of the batteries in the remote control. Something is blocking the remote Make sure nothing is blocking the control signal detector on the display. detector. (If the input signal does not toggle after pressing the INPUT2, OPTION1, or OPTION2 button at least two times) the "Input Setting" for the selected input is set to "Fix". If you want the input signal to toggle with each press of the button, set the "Input Setting" to "Selectable". For details on the "Input Setting", see "Input Setting" on page 19 (GB). 8 The power button and control buttons on the display do not work. In the remote control settings, the "Control Mode" is set to "Remote Only". Check the setting by opening the main menu with the remote control and then selecting "CUSTOM SETUP" t "Remote" t "Control Mode". For details on the "Control Mode", see "Control Mode" on page 19 (GB). 9 Neither the remote control nor a Control S connection can be used to toggle between RGB and YUV (component), or between VIDEO (component video) and S-VIDEO (Y/C). The "Input Setting" for the selected input is set to "Fix". If you want the input signal to toggle with each press of the button, set the "Input Setting" to "Selectable". For details on the "Input Setting", see "Input Setting" on page 19 (GB). 47 (GB)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
47
(GB)
Troubleshooting
Problem
Cause
Remedy
In the remote control settings, the
“Control Mode” is set to “Display Unit
Only”.
A cable is connected to the
CONTROL S IN connector.
The batteries in the remote control are
drained.
Something is blocking the remote
control signal detector on the display.
(If the input signal does not toggle
after pressing the INPUT2, OPTION1,
or OPTION2 button at least two times)
the “Input Setting” for the selected
input is set to “Fix”.
In the remote control settings, the
“Control Mode” is set to “Remote
Only”.
The “Input Setting” for the selected
input is set to “Fix”.
Using the control buttons on the top of
the display, check the setting by opening
the main menu and then selecting
“CUSTOM SETUP”
t
“Remote”
t
“Control Mode”.
For details on the “Control Mode”, see
“Control Mode” on page 19 (GB).
Check the condition of the CONTROL S
IN connector.
The remote control cannot be used while
the display is controlled via a Control S
connection.
Try operating the display by pressing the
power button and control buttons on the
top of the display.
Also, check the condition of the batteries
in the remote control.
Make sure nothing is blocking the
detector.
If you want the input signal to toggle with
each press of the button, set the “Input
Setting” to “Selectable”.
For details on the “Input Setting”, see
“Input Setting” on page 19 (GB).
Check the setting by opening the main
menu with the remote control and then
selecting “CUSTOM SETUP”
t
“Remote”
t
“Control Mode”.
For details on the “Control Mode”, see
“Control Mode” on page 19 (GB).
If you want the input signal to toggle with
each press of the button, set the “Input
Setting” to “Selectable”.
For details on the “Input Setting”, see
“Input Setting” on page 19 (GB).
7
8
9
The remote control does not
work.
The power button and control
buttons on the display do not
work.
Neither the remote control nor a
Control S connection can be used
to toggle between RGB and YUV
(component), or between VIDEO
(component video) and S-VIDEO
(Y/C).