Sony FX52 Operating Instructions - Page 42

Maintenance, Replacing the Lamp

Get Sony FX52 - VPL XGA LCD Projector PDF manuals and user guides
UPC - 027242684263
View all Sony FX52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

B Maintenance Replacing the Lamp The lamp used as a light source is a consumable product. When the lamp has burnt out or dims, or "Please replace the LAMP." appears on the screen, replace the lamp with a new one. Use LMP-F300 Projector Lamp as the replacement lamp. The lamp life varies depending on conditions of use. Caution The lamp becomes a high temperature after turning off the projector with the I / 1 key. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least an hour for the lamp to cool. Notes • If the lamp breaks, consult with qualified Sony personnel. • Pull out the lamp by holding the handle. If you touch the lamp, you may be burned or injured. • When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while tilted and if the lamp is broken, the pieces may scatter, causing injury. • To erase a message, press any key on the control panel of the projector or on the remote commander. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet. Note When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool. 2 Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can see its underside. Note Be sure that the projector is stable after turning it over. 42 Replacing the Lamp 3 Slide to open the lamp cover by loosening one screw with the Phillips screwdriver. Note Be sure not to remove other screws, for safety reasons. 4 Loosen two screws on the lamp unit with the Phillips screwdriver. 5 While holding the handle and keeping the lamp unit horizontal, pull straight up.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
42
Replacing the Lamp
B
Maintenance
Replacing the Lamp
The lamp used as a light source is a
consumable product. When the lamp has
burnt out or dims, or “Please replace the
LAMP.” appears on the screen, replace the
lamp with a new one. Use LMP-F300
Projector Lamp as the replacement lamp.
The lamp life varies depending on
conditions of use.
The lamp becomes a high temperature after
turning off the projector with the
I
/
1
key.
If
you touch the lamp, you may scald your
finger. When you replace the lamp, wait for
at least an hour for the lamp to cool.
•
If the lamp breaks, consult with qualified
Sony personnel.
•
Pull out the lamp by holding the handle. If
you touch the lamp, you may be burned or
injured.
•
When removing the lamp, make sure it
remains horizontal, then pull straight up. Do
not tilt the lamp. If you pull out the lamp
while tilted and if the lamp is broken, the
pieces may scatter, causing injury.
•
To erase a message, press any key on the
control panel of the projector or on the
remote commander.
1
Turn off the projector, and disconnect
the AC power cord from the AC
outlet.
When replacing the lamp after using the
projector, wait for at least an hour for the
lamp to cool.
2
Place a protective sheet (cloth)
beneath the projector. Turn the
projector over so you can see its
underside.
Be sure that the projector is stable after
turning it over.
3
Slide to open the lamp cover by
loosening one screw with the Phillips
screwdriver.
Be sure not to remove other screws, for
safety reasons.
4
Loosen two screws on the lamp unit
with the Phillips screwdriver.
5
While holding the handle and keeping
the lamp unit horizontal, pull straight
up.
Caution
Notes
Note
Note
Note